Multitool TLC
-
I'm almost as bad as Dubya Dawg, with this double posting.
My Security (well not my, some I borrowed) bits didn't fit -
It's possible they were just rubbish bits, and not accurate enough to actually work - or is it possible that Yuessayans use a different size security bit? -
I'm always getting sand in my tools ::) I use compressed air . Not talking about the stuff in a can but a proper compresor. The I use a little brush ( like what you get with an electric razor , or a tooth brush ) , I also use bluetack http://en.wikipedia.org/wiki/Blu-tack . Just push it in all the hard to get places on your multitool and when you pull it out all the crap comes with it . It really does work and you can get right into the really hard to get places . Then its a good scrub with soap and water ( I find washing up liquid best ) and make sure you open and close all the tools several times under water , a rinse then dryed with a hair dryer . Any grains of sand left in the tool you should be able to get out with the blue tack and brush .Lastley a drop of oil .
Dunc
-
I use LPS #2 on my LM Core. I use pure mineral oil on my CRKT M21-14 because I may use it for food prep.
-
I learned this the first week I worked in a restaurant several years ago but just wanted to clarify since it appears I have forgotten.
When cleaning a tool avoid the Green Scouring Pads seen below. They actually scratch the metal and visibly destroy the finish as well as creating an environment that is more conducive to rust.
I used the pads on the PST mentioned earlier in this thread and never noticed because the tool was so used but after scrubbing down a SuperTool and seeing the damage created by the pads I must correct myself.
One should only use stainless steel or copper scrubbers to clean the rust/grime from tools. They work well in conjuction with dishsoap and are easy on the finish but tough on rust.

Tip#2: Toothpaste scrubbed into the pivot points of a used tool with a toothbrush will get rid of the "gummy" feeling that comes from years of use and old 3-in-1 oil. Be careful using this method on riveted and new tools since it is easy to go to far and create loose pivots.
-
I use nothing more abrasive than Cotton for cleaning of tools & knives - I rely on whatever compound is in use to remove crap.
-
WD40 in a pressurized can,fine brush,and Q-tips works for most crud.
-
Def, whatever happened to the graphite/aluminum experiment?
-
-
Is there an echo in here? :P
Absolutely nothing happened. I don't have any pictures of the arrangement I had set up, but basically I had an aluminum liner on a plate, inside a Rubbermaid cake thing- the kind used for transporting cakes. I put water in the inverted Rubbermaid lid, put the plate in the center (the plate kept the scale from actually being in the water), then put the graphite all over the scale. I had even scuffed the scale somewhat to make sure if there was any coating on it, the aluminum would be exposed. I then put the clear lid over the whole thing and let it sit in my kitchen, where the temperature varies greatly depending on the time of day, or whether I am cooking anything. I figured different temps might have different effects.
After about six weeks I gave up on it and cleaned the mess up- the liner had no issues whatsoever.
Def
-
Reading the TLC thread, it seems there are 4 schools of camp when it comes to lubricating multitools:
- WD-40
- Various oils, like 3-in -1, gun oils, etc. either all over on just on joints
- Mineral oil and Inox on joints
- Nothing
I don't know anything about this stuff, but I was instinctively leaning toward nothing, and perhaps using mineral oil or graphite only if the joints became stiff. (That graphite is amazing stuff. I was a convert the first time it miraculously repaired a completely frozen lock with a small squirt.)
Anyway, the majority seem to favour WD-40 or oil of some sort. Is coating the entire tool really necessary? Doesn't it make it greasy and slippery?
-
Since this thread is fresh in my mind, I thought I'd also post a quick summary of cleaning methods for future readers.
This is just off the top of my head, so please excuse any ommissions:
Cleaning:
-
Most people either use WD-40, or water with some sort of soap.
-
For cleaning utensils, people often use rags, toothbrushes, q-tips, & toothpicks
-
Special cleaning methods include:
- Blowing out dirt with a can of compressed air
- Sticking blue tac inside grooves to picks up little bits of dirt, etc.
- Using unwaxed dental floss to clean inside joints of pliers and tools
- Putting SAKs and Vic MTs in the dishwasher
- Opening & closing joints under running water, or while swishing the tool around in water
-
Drying is extremely important. Some people leave the tool opened to air dry. Some use a hair dryer or something similar.
-
-
@max6166 said:
Anyway, the majority seem to favour WD-40 or oil of some sort. Is coating the entire tool really necessary? Doesn't it make it greasy and slippery?I've never done extensive testing or anything, so I can't really say what's entirely necessary. But... I've been using WD-40 for serious cleaning and 3-in-1 for general lube. I just put a small drop on most of the pivots and work it in a bit. Sometimes I wipe some on the blades/tools, but not much. When I'm done I wipe the whole thing off with a cloth (just cut up t-shirts...). It doesn't seem slippery or overly oily to me, though the next couple of times I use the tool I might notice a little oil seeping out. I usually go a while between cleaning/lubing, so that doesn't bother me too much.
-
That's easy, buy it, decide the two of you don't gel, then sell it before the factory oil even wears off. Hmmm, sounds a lot like mickyd. :D
Mike
-
dential floss! I would have never thought about that.
see, I've already learned something new!
ironhand
-
-
I'll be honest. I don't really do much cleaning on my multi tools. I sharpen the knife if it gets dull. I haven't oiled the Pulse in I don't know how long. I oil the blades on the Wave every once in a while with some FP-10 gun oil.
I've used carb & choke cleaner to blast out grit before, or just over-oil the joint and work the pliers for a while. ALl kinds of black stuff comes out every time I do that.
-
I just soak them in warm soapy water over night and then using either a pick or toothpick and pipe cleaners. I get the yucky stuff out.
Using a combo of M3 pads or steel eraser and paste.
But for oil I use olive oil on the pivots and blades. That way when one cuts food they don't get the WD 40 taste.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
:D