Single-wing Wingman
-
Andrew. Have you shown anyone at Leatherman yours? If so what were their thoughts?
-
Literally just made it tonight. Going to take it to work tomorrow to show off. I did show my supervisor this thread and he thought it was a cool idea.
-
@AndrewBird said:
Literally just made it tonight. Going to take it to work tomorrow to show off. I did show my supervisor this thread and he thought it was a cool idea.Very cool.

-
@AndrewBird said:
Literally just made it tonight. Going to take it to work tomorrow to show off.I'm humbled that a Leatherman tool maker found this mod interesting enough to have a go at it too, you made my day Andrew ;)
I have few more ideas in my head with other LM tools, one specific mod involves a LM MUT but unfortunately life just became a little more complicated and cannot afford time nor money for hobbies and similar. Maybe one day :-\
@AndrewBird said:
I did show my supervisor this thread and he thought it was a cool idea.Say hi to your supervisor :)
-
Everyone I showed it to liked it. One of the engineers even wants to make one for himself.
I've been using it at work and it is nice to use. The blade is a bit hard to open one handed due to how narrow the whole thing is, but otherwise it's comfortable to use. I'll probably start using this as my EDC for work instead of my Kershaw Leek. Keep that for the weekends. And of course still carry my Skeletool.
-
@AndrewBird said:
Everyone I showed it to liked it. One of the engineers even wants to make one for himself.I've been using it at work and it is nice to use. The blade is a bit hard to open one handed due to how narrow the whole thing is, but otherwise it's comfortable to use. I'll probably start using this as my EDC for work instead of my Kershaw Leek. Keep that for the weekends. And of course still carry my Skeletool.
Very cool!

-
@AndrewBird said:
Everyone I showed it to liked it. One of the engineers even wants to make one for himself.Just ler me know who to send the bank acct details over there, time to start collecting some royalties...LOL ! :D
Thanks man...this is all very cool.

-
Cool

-
I hope this makes into production line. It'd be the coolest Leatherman.
-
@Glofindel said:
I hope this makes into production line. It'd be the coolest Leatherman.hopefully the make the handle a little wider.
-
Is the plier pivot on the Rev the same size as the Wingman/Sidekick? If so, I think it'd save a step to use the Rev instead for this mod, since you wouldn't have to drill out the rivet holding the retention spring of the Wingman/Sidekick plier.
At least... I think I have that right.
I pulled my mod out today and was fiddling with it. And still think it's a pretty cool idea. The pocket clip is just really useful for a knife this size, IMO.
-
@Lynn LeFey said:
Is the plier pivot on the Rev the same size as the Wingman/Sidekick? If so, I think it'd save a step to use the Rev instead for this mod, since you wouldn't have to drill out the rivet holding the retention spring of the Wingman/Sidekick plier.At least... I think I have that right.
I pulled my mod out today and was fiddling with it. And still think it's a pretty cool idea. The pocket clip is just really useful for a knife this size, IMO.
I treid do that with rev, did not work.
-
Huh.
What went wrong?
-
@Kampfer said:
This thing is so easy, took less than two minutes to take apart and put back together.I tried putting the drivers on the other end of handle in place of pliers, they fit in but don not click, their locking lugs could not reach the handle. It would be good if the drivers can directly drop in take place of pliers, average user can easily transform the tool to "Pocket knife" or "Pocket pliers" modes, sadly that is not the case.
I tried putting Rev's pliers on SK, but they don't fit either.
-
babola, I hope you do not mind, but I stole your pics and link to show someone on another forum.
-
Sorry, not read the whole thread, but curious if you used the other handle (with scissors) you could make it TSA compliant.
It wouldnt have a blade, but still have a lot of great tools in a small package -
Making a YouTube video "Simple Leatherman Wingman Modifications" showing step by step how to do it will be very helpful, I'm sure it will have a lot of hits and thumbs up. Who knows, but you might get a call from LM ;)
-
@babola said:
I was pretty sure this had been done before by some of the modders here, as it's such a logical and straightforward way to finish up with by following the Mini-Surge mod. I am currently collecting bits for my own Mini-Surge mod, Wingman scissors being one of them.This left me with a scissor-less Wingman, and since I am OCD and cannot stand Wingman pliers I decided to create a 'mini-tool folder' in a single Wingman handle.
What made this mod easier was the fact the top (pliers-end) and bottom (tools-end) pivot sizes on Wingman are the same size, allowing me to install the tools from a bottom of one handle into the top of the other, basically combining the Wingman's tool load into a single handle. To top it all off, I also added scissors from the Wave.
The result was quite surprising to me as it required very little modding while creating almost a perfect small 'MT-folder' as an end result.
The top tools fit snugly into the handle and the Wave scissors fold in perfectly. The only rule of thumb is to fold the bottom tools into the handle first, and top tools second, on top of the bottom tools. This is required as there's simply not enough space for the tools to fold independently inside the main handle cavity due to their length.
Few details:
- I used a Wingman handle housing a 420HC combo blade
- Bottom tools in that handle were left untouched
- Internal pliers stop strip had to be removed by breaking a rivet, to allow the installation of the tools at the top of the handle. This is a must.
- Phillips and flat head screwdrivers from the second handle were installed at the top of this handle
- Wave scissors added and installed in a particular position (see photos below) over the bottle/can opener for correct fit
- After extensive play with different sized washers and spacers (all sourced from Wingman's second handle) I ended up with this combo.
- All button screw heads flattened. As much as I like button heads their prominent bulge was a little out of place for me personally on this tool, they are much bigger than the ones on Wave/Charge/Surge.












Hope you like it :)
Awesome! [emoji482][emoji106]
-
I bought the Wingman to replace a Sideclip that was lost. I never really warmed up to the Wingman.
So what to do. You read some post on MTO and take your tool apart. Makes perfect sense right?
Not having mills or surface grinders, not to mention the skills of some here. I had to come up with a way to pull off this mod, that I could do it in my garage.
I tried it with one end not clicking into place and even though it worked I kept thing there must be a way to make both ends of the tool snap into place.
.
So I decided to rivet the spring from one handle to the blade side handle.
First step is to drill out the rivet for the pliars head spring.
Next step is to cut out a clearance on the bottom for the spring.
Then you have to grind the retaining lugs off the spring. So it will fit into the handle.
Then install the spring with one of the hinge screws. Don't take the hinge screw out until you are done.
This will hold it in place when you drill the hole for the 3/32nd SS rod. I used stock from a knife supply that's sold for slip joints. Leave the hinge screw in place while you are peening the rod, so it will stay in position. If it moves now you are in trouble.I used a punch and doomed the end so I could peen the rod inside the handle. Then clamped the punch in a vice so it would back up the rod. Then worked the other end with a small ball peen.




Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login