The Mega84
-
..... has begun :ahhh :ahhh :ahhh
There's a couple of SAK mods I've been considering for quite a while, and after a lot of patient searching and spending, I finally got the parts together that I needed about 12-18 months ago. Since then those donor knives have just sat in a drawer, untouched (though occasionally carried/used) ::)
I've spoken about doing SAK mods, bought donors, sold pin stock, and even advised on doing SAK mods, but never actually completed anything more than a scale swap
Time for that to change, and the whole point of me making this opening post is to make it significantly more difficult for me to bail out of the uncompleted project 
Obviously, the advice given is to start small and do a simple cheap mod which doesn't matter if you wreck it, and obviously I've completely ignored that and gone for the most expensive and ambitious project first
Two of the five (yes five) donors are broken down, the first ambitious part of the project has revealed that it's not as straight forward as I'd hoped (needs some thought and careful grinding), and my right thumb has failed a N_N_R style impromptu skin durability test 
More to follow later, once I've overcome the first obstacle....
-
Crap!!! IDIOT!!!!
Third knife apart, second problem becomes apparent, and it's a biggie!

This is going to need some careful thought.....
....more careful than before ::) -
This could be at least a three beer problem. First one is open already, so remedial planning is underway
-
This should be good.
:D -
Nothing like making a rod for your own back!
I’m going to sit here and watch now Mate

(Yep its a three popcorn thread )
-
I was like this with my CS go phillips mod,waited ages too do it,but once i did it i was surprised at how easy it was,ill be watching with anticipation

-
Beer number one finished
So....
Problem two is bigger than problem one
I may be able to fix problem two. Unconventional, but could work
I have enough tools for three attempts at solving problem two, but there is a risk of causing backspring issues, and I only have one spare backspring.
If problem two is not solved, this might mean I have to address problem one in a different way
I need to get problem one fixed first time, as there are no spare tools
Therefore, solution for problem two needs a test build to prove the concept.
Once the tools are modified and concept proven, they can be reused in the finished build and I'm all clear to regrind to other tool to fix problem one
..... I think

Beer number two opened
-
When you get to beer #6 you'll figure it all out
-
Shouldn't this be the Mega 85? ;)
You were talking about a mod on a Wenger Nomad for the last few years if I remember correctly.

-
Beer number two completed. No success. Engage cheat mode!
If the questions keep giving you answers you don't like, start asking different questions. Let's look at the whole problem differently....
Commence beer three.
-
Well I've been doing my 84mm mod for the last 3 years and it's still in parts.

And my 85mm Urban will probably be taken apart and redone in a different configuration soon. For the 4th time. Or is it 5th.

So yes, I understand your pain. ;)
-
Whether or not this works well enough, influences what goes up for sale next. I kind of need to do the awkward one to know if the easier ones are worth doing. The ironic part though is that to build this awkward one, I'm actually breaking down a few knives that are hard to come by.
If I can get this one to work, it's more likely to see frequent pocket duty than the other two mods I have planned. It won't work as I originally imagined it, but I just need to decide which feature to sacrifice in order to retain the others
-
Ok, here goes.... this was the original plan:
***93mm Awl Plain Blade
(corkscrew with mini driver)Scissors
Saw
Nail file Serrated Blade
(round can key Phillips mounted backwards)Bottle Opener Can Opener
(awl slot vacant to allow space for reversed Phillips)***Problem 1:
93mm awl sits way too high. IF the awl remains in this position, a modified kick should allow it to drop low enough to have the point below scale height.Problem 2:
The tang on the Phillips is not symmetrical like I thought, which means it can't be reversedOption one:
Bring serrated blade layer forwards to allow Phillips to be kept in same orientation. This moves the can opener back a layer, plus one extra spacer (needed as awl backspring isn't quite thick enough to provide a big enough void). This means the can opener might work on some smaller diameter cans, but not on larger ones.Option two:
As option one, but grind can opener into a technicians driverOption three:
Shorten tang on Phillips and re-drill at the other side. This allows a slightly shorter Phillips to be inversely mounted. Liners would need modifying, and this is VERY risky, with no second chancesOption four:
Shorten tang on CORKSCREW and reduce the other end by half a turn to put the point "safe" when mounted backwards. Mount Phillips "correctly" in outer slot.Option five:
As option two, but ditch the awl and use combo tool to recover can opening ability -
Tools broken down so far are Rancher, MFV+, and Sportsman
-
I reversed a phillips on a Ti 91mm mod and boy what a pain! I filled the hole with brass, then drilled a new hole, AND had to change the angled part of the part that mates with the back scale.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login