The Mega84
-
When you get to beer #6 you'll figure it all out
-
Shouldn't this be the Mega 85? ;)
You were talking about a mod on a Wenger Nomad for the last few years if I remember correctly.

-
Beer number two completed. No success. Engage cheat mode!
If the questions keep giving you answers you don't like, start asking different questions. Let's look at the whole problem differently....
Commence beer three.
-
Well I've been doing my 84mm mod for the last 3 years and it's still in parts.

And my 85mm Urban will probably be taken apart and redone in a different configuration soon. For the 4th time. Or is it 5th.

So yes, I understand your pain. ;)
-
Whether or not this works well enough, influences what goes up for sale next. I kind of need to do the awkward one to know if the easier ones are worth doing. The ironic part though is that to build this awkward one, I'm actually breaking down a few knives that are hard to come by.
If I can get this one to work, it's more likely to see frequent pocket duty than the other two mods I have planned. It won't work as I originally imagined it, but I just need to decide which feature to sacrifice in order to retain the others
-
Ok, here goes.... this was the original plan:
***93mm Awl Plain Blade
(corkscrew with mini driver)Scissors
Saw
Nail file Serrated Blade
(round can key Phillips mounted backwards)Bottle Opener Can Opener
(awl slot vacant to allow space for reversed Phillips)***Problem 1:
93mm awl sits way too high. IF the awl remains in this position, a modified kick should allow it to drop low enough to have the point below scale height.Problem 2:
The tang on the Phillips is not symmetrical like I thought, which means it can't be reversedOption one:
Bring serrated blade layer forwards to allow Phillips to be kept in same orientation. This moves the can opener back a layer, plus one extra spacer (needed as awl backspring isn't quite thick enough to provide a big enough void). This means the can opener might work on some smaller diameter cans, but not on larger ones.Option two:
As option one, but grind can opener into a technicians driverOption three:
Shorten tang on Phillips and re-drill at the other side. This allows a slightly shorter Phillips to be inversely mounted. Liners would need modifying, and this is VERY risky, with no second chancesOption four:
Shorten tang on CORKSCREW and reduce the other end by half a turn to put the point "safe" when mounted backwards. Mount Phillips "correctly" in outer slot.Option five:
As option two, but ditch the awl and use combo tool to recover can opening ability -
Tools broken down so far are Rancher, MFV+, and Sportsman
-
I reversed a phillips on a Ti 91mm mod and boy what a pain! I filled the hole with brass, then drilled a new hole, AND had to change the angled part of the part that mates with the back scale.

-
@Syph007 said:
I reversed a phillips on a Ti 91mm mod and boy what a pain! I filled the hole with brass, then drilled a new hole, AND had to change the angled part of the part that mates with the back scale.Thanks Robert

Personally I considered filling the hole, but using brass could lead to galling (brass on brass) and I'd have to use a drill press with a core drill to avoid push off between the two metals and stop it favouring the brass.
I'm using a cordless drill on my kitchen table

Only other option for me would be to go and have a work with an old mate to see if he could TIG weld it up for me, then grind flush, then drill. Risks there are thermal distortion, and if the weld chills I'm back to needing a drill press
EDIT: gorgeous looking mod BTW

-
Oh for the 93mm awl, you have to relocate the pivot hole on that one as well and regrind the pivot to be the same shape as the other 84mm tools. It works as is on a 91, but not on an 84.
-
Oh, I was just going to regrind the kick so it closed further. Will that not work? I realised the arse end will be stuck up a bit, but didn't think it was a full tang rework. Was it just to get it to sit parallel, or is there something else I've missed (so I know what to watch for when I'm doing it)
-
I think tomorrow I'm going to try option 2 as described above and see how it works out. All I'm sacrificing is one can opener, and there'll be a couple of spares from the other donors if I change my mind later.... in fact I might as well build it up in tact first (option 1), and see what cans it might work on.
I know the awl will sit dangerously high at this stage, but it'll give me an overall feel of the knife and guide me as to subsequent changes.
-
@50ft-trad said:
Oh, I was just going to regrind the kick so it closed further. Will that not work? I realised the arse end will be stuck up a bit, but didn't think it was a full tang rework. Was it just to get it to sit parallel, or is there something else I've missed (so I know what to watch for when I'm doing it)Ya I did it that way to it would sit parallel. :D
84mm modding is a pain!



-
Thanks mate
That makes more sense now. I'll do the test build tomorrow and see how sensible everything looks. I'd rather not go to that extent on the tangs if I can help it, and I need to see if I can make it work (for me) a different / easier way. I don't have the time or facilities for anything too elaborate. Grinding a little off here or there is one thing, but reforming and redrilling entire tangs is not what I had in mind :D -
All knives are now apart, and the micrometer and vernier calipers have come out to play. Due to the assorted ages of the knives, the main blades vary from 2.0mm to 2.4mm. This actually does me a favour though, as the tang on the 93mm awl is thicker than a standard 84mm nail file, small blade, or combo tool.
Awl plus segmented spacer = 2.8mm, so I need the thicker spring. However, the thicker spring only measures 2.3mm. I also need to use selective assembly on the liners too. They have differing offsets where they have been stamped, giving different effective thickesses at different points, and I also need to carefully choose another layer for modification. Due to the configuration of the knife, I need three liners with the corkscrew/phillips cutout, but out of these five donors I only have two (from the Salesman and Sportsman).
Once I've matched everything up as good as possible, modified the liners and tangs as necessary, I still need to make a couple more decisions; firstly whether any additional washers are needed to get smooth function but also let the scales sit flat, and secondly whether to use any of the stock scales or something different

-
Cutting up the b/s awl to make a tapered backspring support with no vice a cordless drill and a few handtools is f-f-f-frustrating to say the least

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login