Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Home solution for loose pliers pivot! Experiment!

Scheduled Pinned Locked Moved Leatherman Tools
96 Posts 1 Posters 19.7k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. Home solution for loose pliers pivot! Experiment!
Home solution for loose pliers pivot! Experiment!
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • aikon2014 Offline
    aikon2014
    Posts: 164
    aikon2014 Offline
    aikon2014
    wrote on last edited by
    #79 Quote Reply

      @Sam Lim said:

      @aikon2014 said:

      Btw is there any way of tightening small tools like micra, style ps, squirts and so on?

      Smallish tools peening with a punch and hammer would be best. Do it lightly though. Very lightly. Test and do again if needed.

      It worked! Tested it on both my Micra and Style CS, both scissors had a small play in it. Took a phillips head screqdriver (rather large one so the smal flat portion on the tip fit the round pivot) and whacked it with a hammer, small whacks first until I found the right force, and tadaa it worked like a charm! I suppose that there are other tools that are moore suited for this, but it worked, no play at all!
      Thanks!

      1 Reply Last reply
      • ThePeacent Offline
        ThePeacent
        Posts: 14,599
        ThePeacent Offline
        ThePeacent
        wrote on last edited by
        #80 Quote Reply

          why isn't this thread a sticky yet?! :ahhh ???

          1 Reply Last reply
          • aikon2014 Offline
            aikon2014
            Posts: 164
            aikon2014 Offline
            aikon2014
            wrote on last edited by
            #81 Quote Reply

              For the record I did put the tool itself outside of the edge of the table and put only the plierhead/scissorhead on the table to prevent ut all from bending. Just a small warning if anyone tries this :D

              1 Reply Last reply
              • aikon2014 Offline
                aikon2014
                Posts: 164
                aikon2014 Offline
                aikon2014
                wrote on last edited by
                #82 Quote Reply

                  Btw, is there a way to do this to a OHT?
                  The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
                  All the others might have been looser in the action than I like, but no play.

                  Anyone tried something to fix the OHT pliers? :)

                  1 Reply Last reply
                  • Sam Lim Offline
                    Sam Lim
                    Posts: 2,306
                    Sam Lim Offline
                    Sam Lim
                    wrote on last edited by
                    #83 Quote Reply

                      @aikon2014 said:
                      Btw, is there a way to do this to a OHT?
                      The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
                      All the others might have been looser in the action than I like, but no play.

                      Anyone tried something to fix the OHT pliers? :)

                      I did. The turning method didn't work on OHT pliers. The pivot is extremely tough. U can hit it pretty hard with the peening method with very little visible scarring. But from factory, most OHT I have seen have some form of misalignment at the tip. I have never seen one thats perfect before.

                      1 Reply Last reply
                      • aikon2014 Offline
                        aikon2014
                        Posts: 164
                        aikon2014 Offline
                        aikon2014
                        wrote on last edited by
                        #84 Quote Reply

                          @Sam Lim said:

                          @aikon2014 said:

                          Btw, is there a way to do this to a OHT?
                          The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
                          All the others might have been looser in the action than I like, but no play.

                          Anyone tried something to fix the OHT pliers? :)

                          I did. The turning method didn't work on OHT pliers. The pivot is extremely tough. U can hit it pretty hard with the peening method with very little visible scarring. But from factory, most OHT I have seen have some form of misalignment at the tip. I have never seen one thats perfect before.

                          It's such a shame :( I would love to have a single hand tool for fishing situations, but no dice with the OHT :(

                          1 Reply Last reply
                          • Sam Lim Offline
                            Sam Lim
                            Posts: 2,306
                            Sam Lim Offline
                            Sam Lim
                            wrote on last edited by
                            #85 Quote Reply

                              @aikon2014 said:

                              @Sam Lim said:

                              @aikon2014 said:

                              Btw, is there a way to do this to a OHT?
                              The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
                              All the others might have been looser in the action than I like, but no play.

                              Anyone tried something to fix the OHT pliers? :)

                              I did. The turning method didn't work on OHT pliers. The pivot is extremely tough. U can hit it pretty hard with the peening method with very little visible scarring. But from factory, most OHT I have seen have some form of misalignment at the tip. I have never seen one thats perfect before.

                              It's such a shame :( I would love to have a single hand tool for fishing situations, but no dice with the OHT :(

                              Well most still grip and cut without any noticeable problems. So I think it's still a good tool.

                              1 Reply Last reply
                              • Syncop8r Offline
                                Syncop8r
                                Posts: 8,801
                                Syncop8r Offline
                                Syncop8r
                                wrote on last edited by
                                #86 Quote Reply

                                  Some discussion about it here: /post/1575499

                                  1 Reply Last reply
                                  • aikon2014 Offline
                                    aikon2014
                                    Posts: 164
                                    aikon2014 Offline
                                    aikon2014
                                    wrote on last edited by
                                    #87 Quote Reply

                                      I just did the method on my new Juice S2, interesting enough, I had to turn it counter clockwise, unlike the Rebars and Wave's which I did clockwise to tighten.
                                      I first tried to do clockwise with the Juice, and it loosened, so I reversed it and it tightened. I wonder why. I had the non "rotating" surface up on all the tools while doing this.

                                      1 Reply Last reply
                                      • aikon2014 Offline
                                        aikon2014
                                        Posts: 164
                                        aikon2014 Offline
                                        aikon2014
                                        wrote on last edited by
                                        #88 Quote Reply

                                          Sam Lim have the fix of the pliers kept and worked in the long run for you? I haven't tried mine for long enough to be able to tell.

                                          1 Reply Last reply
                                          • Sam Lim Offline
                                            Sam Lim
                                            Posts: 2,306
                                            Sam Lim Offline
                                            Sam Lim
                                            wrote on last edited by
                                            #89 Quote Reply

                                              @aikon2014 said:
                                              Sam Lim have the fix of the pliers kept and worked in the long run for you? I haven't tried mine for long enough to be able to tell.

                                              To be very honest, me neither... But so far it held up.

                                              1 Reply Last reply
                                              • ed_is_dead Offline
                                                ed_is_dead
                                                Posts: 107
                                                ed_is_dead Offline
                                                ed_is_dead
                                                wrote on last edited by
                                                #90 Quote Reply

                                                  Hope it's OK to ressurect this thread but I gave this a twirl, pun intended, and it worked.
                                                  I used my crunch to do it to a pst which had a slight but perceptible wobble on.
                                                  20 degrees counter clockwise was enough to bind the plier, 10 degrees was just so and has the wire snips cutting paper like our Tim demonstrates post nail cutting extravaganza on his charge.
                                                  You can see the brushed lines show the rotation and yes I did mar the pliers, the crunch wouldn't turn it unless it got a bite on it.
                                                  Previously I used the ball pien method but this is better imo. Deffo worth doing.

                                                  20230413_163622.jpg

                                                  1 Reply Last reply
                                                  • Poncho65 Offline
                                                    Poncho65
                                                    Global Moderators
                                                    Posts: 88,523
                                                    Poncho65 Offline
                                                    Poncho65
                                                    Global Moderators
                                                    wrote on last edited by
                                                    #91 Quote Reply

                                                      Awesome that this worked out for you, ed :woohoo: :like: :like:

                                                      1 Reply Last reply
                                                      • Adam5 Offline
                                                        Adam5
                                                        Posts: 8,411
                                                        Adam5 Offline
                                                        Adam5
                                                        wrote on last edited by
                                                        #92 Quote Reply

                                                          It is worth a little marring to have the pliers working well again. Good job :tu:

                                                          1 Reply Last reply
                                                          • ed_is_dead Offline
                                                            ed_is_dead
                                                            Posts: 107
                                                            ed_is_dead Offline
                                                            ed_is_dead
                                                            wrote on last edited by
                                                            #93 Quote Reply

                                                              Thanks Poncho and Adam, yea I have ocd issues with plier slop and if the wire cutter doesn't cut paper I usually pull out the hammer, but this is far better.
                                                              I don't mind the bite mark on this tool, it's a hard user but will investigate using copper washers something?

                                                              1 Reply Last reply
                                                              • SteveC Offline
                                                                SteveC
                                                                Global Moderators
                                                                Posts: 73,535
                                                                SteveC Offline
                                                                SteveC
                                                                Global Moderators
                                                                wrote on last edited by
                                                                #94 Quote Reply

                                                                  @ed_is_dead said:
                                                                  Hope it's OK to ressurect this thread but I gave this a twirl, pun intended, and it worked.
                                                                  I used my crunch to do it to a pst which had a slight but perceptible wobble on.
                                                                  20 degrees counter clockwise was enough to bind the plier, 10 degrees was just so and has the wire snips cutting paper like our Tim demonstrates post nail cutting extravaganza on his charge.
                                                                  You can see the brushed lines show the rotation and yes I did mar the pliers, the crunch wouldn't turn it unless it got a bite on it.
                                                                  Previously I used the ball pien method but this is better imo. Deffo worth doing.

                                                                  :like: :tu:

                                                                  1 Reply Last reply
                                                                  • m47mu74nt Offline
                                                                    m47mu74nt
                                                                    Posts: 2,520
                                                                    m47mu74nt Offline
                                                                    m47mu74nt
                                                                    wrote on last edited by
                                                                    #95 Quote Reply

                                                                      :like: :like:

                                                                      1 Reply Last reply

                                                                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                      With your input, this post could be even better 💗

                                                                      Register Login

                                                                      • 1
                                                                      • 2
                                                                      • 3
                                                                      • 4
                                                                      • 5
                                                                      1. Home
                                                                      2. Tool Talk
                                                                      3. Leatherman Tools
                                                                      4. Home solution for loose pliers pivot! Experiment!
                                                                      Reply
                                                                      • Reply as topic
                                                                      Log in to reply
                                                                      COMMUNITY LINKS
                                                                      EDC-TV SAKWiki GearFeed SAKSelector
                                                                      Operational Funds

                                                                      Help us keep the Unworkable working!

                                                                      Make A Donation
                                                                      November Goal: $300.00
                                                                      Due Date: Nov 30
                                                                      Total Receipts: $0.00
                                                                      Below Goal: $300.00
                                                                      0% funded
                                                                      • Login

                                                                      • Don't have an account? Register

                                                                      • Login or register to search.
                                                                      • First post
                                                                        Last post
                                                                      0