Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Home solution for loose pliers pivot! Experiment!

Scheduled Pinned Locked Moved Leatherman Tools
96 Posts 1 Posters 19.7k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. Home solution for loose pliers pivot! Experiment!
Home solution for loose pliers pivot! Experiment!
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Syncop8r Offline
    Syncop8r
    Posts: 8,801
    Syncop8r Offline
    Syncop8r
    wrote on last edited by
    #86 Quote Reply

      Some discussion about it here: /post/1575499

      1 Reply Last reply
      • aikon2014 Offline
        aikon2014
        Posts: 164
        aikon2014 Offline
        aikon2014
        wrote on last edited by
        #87 Quote Reply

          I just did the method on my new Juice S2, interesting enough, I had to turn it counter clockwise, unlike the Rebars and Wave's which I did clockwise to tighten.
          I first tried to do clockwise with the Juice, and it loosened, so I reversed it and it tightened. I wonder why. I had the non "rotating" surface up on all the tools while doing this.

          1 Reply Last reply
          • aikon2014 Offline
            aikon2014
            Posts: 164
            aikon2014 Offline
            aikon2014
            wrote on last edited by
            #88 Quote Reply

              Sam Lim have the fix of the pliers kept and worked in the long run for you? I haven't tried mine for long enough to be able to tell.

              1 Reply Last reply
              • Sam Lim Offline
                Sam Lim
                Posts: 2,306
                Sam Lim Offline
                Sam Lim
                wrote on last edited by
                #89 Quote Reply

                  @aikon2014 said:
                  Sam Lim have the fix of the pliers kept and worked in the long run for you? I haven't tried mine for long enough to be able to tell.

                  To be very honest, me neither... But so far it held up.

                  1 Reply Last reply
                  • ed_is_dead Offline
                    ed_is_dead
                    Posts: 107
                    ed_is_dead Offline
                    ed_is_dead
                    wrote on last edited by
                    #90 Quote Reply

                      Hope it's OK to ressurect this thread but I gave this a twirl, pun intended, and it worked.
                      I used my crunch to do it to a pst which had a slight but perceptible wobble on.
                      20 degrees counter clockwise was enough to bind the plier, 10 degrees was just so and has the wire snips cutting paper like our Tim demonstrates post nail cutting extravaganza on his charge.
                      You can see the brushed lines show the rotation and yes I did mar the pliers, the crunch wouldn't turn it unless it got a bite on it.
                      Previously I used the ball pien method but this is better imo. Deffo worth doing.

                      20230413_163622.jpg

                      1 Reply Last reply
                      • Poncho65 Offline
                        Poncho65
                        Global Moderators
                        Posts: 88,523
                        Poncho65 Offline
                        Poncho65
                        Global Moderators
                        wrote on last edited by
                        #91 Quote Reply

                          Awesome that this worked out for you, ed :woohoo: :like: :like:

                          1 Reply Last reply
                          • Adam5 Offline
                            Adam5
                            Posts: 8,411
                            Adam5 Offline
                            Adam5
                            wrote on last edited by
                            #92 Quote Reply

                              It is worth a little marring to have the pliers working well again. Good job :tu:

                              1 Reply Last reply
                              • ed_is_dead Offline
                                ed_is_dead
                                Posts: 107
                                ed_is_dead Offline
                                ed_is_dead
                                wrote on last edited by
                                #93 Quote Reply

                                  Thanks Poncho and Adam, yea I have ocd issues with plier slop and if the wire cutter doesn't cut paper I usually pull out the hammer, but this is far better.
                                  I don't mind the bite mark on this tool, it's a hard user but will investigate using copper washers something?

                                  1 Reply Last reply
                                  • SteveC Offline
                                    SteveC
                                    Global Moderators
                                    Posts: 73,535
                                    SteveC Offline
                                    SteveC
                                    Global Moderators
                                    wrote on last edited by
                                    #94 Quote Reply

                                      @ed_is_dead said:
                                      Hope it's OK to ressurect this thread but I gave this a twirl, pun intended, and it worked.
                                      I used my crunch to do it to a pst which had a slight but perceptible wobble on.
                                      20 degrees counter clockwise was enough to bind the plier, 10 degrees was just so and has the wire snips cutting paper like our Tim demonstrates post nail cutting extravaganza on his charge.
                                      You can see the brushed lines show the rotation and yes I did mar the pliers, the crunch wouldn't turn it unless it got a bite on it.
                                      Previously I used the ball pien method but this is better imo. Deffo worth doing.

                                      :like: :tu:

                                      1 Reply Last reply
                                      • m47mu74nt Offline
                                        m47mu74nt
                                        Posts: 2,520
                                        m47mu74nt Offline
                                        m47mu74nt
                                        wrote on last edited by
                                        #95 Quote Reply

                                          :like: :like:

                                          1 Reply Last reply

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          • 1
                                          • 2
                                          • 3
                                          • 4
                                          • 5
                                          1. Home
                                          2. Tool Talk
                                          3. Leatherman Tools
                                          4. Home solution for loose pliers pivot! Experiment!
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          COMMUNITY LINKS
                                          EDC-TV SAKWiki GearFeed SAKSelector
                                          Operational Funds

                                          Help us keep the Unworkable working!

                                          Make A Donation
                                          November Goal: $300.00
                                          Due Date: Nov 30
                                          Total Receipts: $0.00
                                          Below Goal: $300.00
                                          0% funded
                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0