Show us your fixed blades
-
@Benner said:
I like the look of those. They look like they can withstand a lot of abuse.There is nowt girlie about them that's for sure. :D One of the reasons I'd never carry it as a stand alone knife is the near total lack of a point. So given that's the case, and I then have to carry a smaller fixed blade, then I would carry an axe instead of the MOD knife. I suppose if I had a fixed camp and could take more than what I'm prepared to carry on my back it would make for a good supplementary knife.
-
I just got a new JRE sheath in for my EnZo Trapper so I had to take some pics.
The Trapper is one of the earlier blades in 0-1. Scales are Maple Burl with brass bolts and lanyard tube. The JRE sheath is the F1 Gundy model with a drop loop added. Originally intended for a Fallkniven F1, but it fits the Trapper perfectly.


-
The grip tape circle is meant to be a striker for the strike anywhere matches, correct?
-
Yes, it works well if you use a light touch...otherwise it can rip the heads off.
-
Pukka leather work that

-
Where do you get your "strike anywhere" matches Spork?
-
Corrugated, check your local Army Barracks type stores.. My local AB has tons!
-
@Corrugated said:
Where do you get your "strike anywhere" matches Spork?I usually get mine at OSH (Orchard Supply Hardware)...I think it's a chain is confined to California though.

-
-
Now that is a VERY fine blade sir

I'm bloody envious mate

-
That is gorgeous

-
That is very nice mate

-

hand forged 120mm x 5mm bushcraft knife,has two sharpening angles,for chopping and "whittling",and the end of handle is hardened to act as firesteel.
and good old m95 with fallkniven s1.
these i haul with me in school,not all,but one at the time.nothing special or fany but these have been proved to be sturdy,take some batoning easily and easy to sharpen...except for that oddball convex-S1.but the convx will be history and it will have scandi grind.
-
I made the sheath for this Victorinox Rabbit knife today :P


-
What do you use it for mate ???
I'm assuming only for really light duties :)
-
Not quite sure yet...it is the only knife in the Fibrox line that looks like it might work as a field knife. The reason it is called a Rabbit knife is that it is intended for boning rabbit...and I assume other game animals.
The blade itself is a stiff wide boning type, at the spine it is about the same thickness as a Mora Clipper.
I sharpened it as I would a SAK...widened the secondary bevel a bit and rounded the shoulder on sandpaper to a slight convex. It is stupidly sharp and makes shavings easily on the poplar and cedar I tried it on.
While I would not carry it as a primary, it would work well as a Bird-and-Trout...as well as a camp kitchen knife.
It only cost $10 and I thought I would give it a go and see what it is capable of.
-
Here's my old LL Beans Trout knife...basically a flexible narrow boner...carbon steel and also capable of getting stupidly sharp. Cleaned a lot of trout and squirrels with this one in my teens...back when I only had a couple of knives :P

-
Lovely patina on the trout knife mate

-
I think that patina is older than Benner...I've had that knife since about 1976 :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

