Knot in October GAW
-
Oh, and I know I get one entry, I just wanted to share something more elaborate than just a figure 8 so I connected two knots in one entry

And I really should go get my red auxiliary rope from my gear bag, these two are too similar for contrast

-
My second knot entry is the Double Constrictor knot.

1)Start with the standing end dangling in front of the object you want to tie the double constrictor knot around
2)Wrap the working end over and around the object
Wrap the working end over and around the object again, this time being sure to cross over the standing end
3) Wrap the working end around again, over the standing end and next to the previous wrap
4) As the working end is brought around go over the dangling standing end then under the wraps going between the original wrap and the two that crossed over the standing end
5) Pull tight on both standing and working endIn some ways this knot is like a hitch, but more secure and not meant to be untied. It can also be used
- like a clamp to hold over lapping objects together where at least one is soft or pliable, like a hose onto a pipe
- If a line gets cut or parts, can use a constrictor knot at end to help prevent fraying
- if a hose breaks and need to secure end to stop or minimize leaking. The effectiveness would depend on pressure and pliability of hose.
- lanyard or tie down for an item that does not have a hole to run a line thru, such as pen, water bottle, flashlight, etc.
The biggest downsides to the double constrictor knot are
- that it can become so tight that it cannot be untied and needs to be cut
- if wrapped around something soft or pliable, it can crush the item as it tightens, for instance two hoses that you want to maintain flow through
Here is the double constrictor knot before tightening around a water bottle

Here is it after tightening and swinging the full bottle around

Here is it used as part of a lanyard for a flashlight

Here is the double constrictor knot tightened around a can. The can was crushed simply by pulling the knot tight

-
:ahhh

I use the single Constrictor knot a good bit: most often to secure a hank of rope and keep it from unraveling. You've inspired me to try the Double Constrictor now!
I often tie my single Constrictor with slippery bight to make untying a bit easier. (As you said, these things can be cinched down pretty tight!)
As I type, here is a hanked line, ready for practice knots, secured with a 'slippery constrictor':

Ashley has a neat cartoon of a technique to really cinch down a constrictor (for making a hose clamp repair in this instance):

The Constrictor is tied with long tails, these are attached to dowels. Now pressure can be applied using the force of legs, back and arms! I bet that don't come untied easily......
Thanks for a great knot!

-
Inspired by Sos24 and Ashley, I tried tying the Double Constrictor using a bight around a dowel:

The bight let me stick my foot in the loop and then pull from the other side with my arms. Man, oh man! This got tight!
It was hard to slide it off the dowel.
I tried the same knot using just the single line, not doubled up. I put a Bowline in one tail for my foot and pulled on the other tail with my arms.
I think this version got even tighter!
As I pulled, I noticed the cols of line sliding past each other, tightening like a Boa Constrictor on its prey. When the line was doubled over, I don't think it could slip on itsself quite as well, and so may not have gotten quite as tight as the single line version.
The Double Constrictor is definitely a keeper!

-
Great knots. I was hoping someone would do the figure 8. I love the beauty of this knot. The constrictor knot is one I also am glad to see. I need to memorize this one for sure.
-
Great contributions everyone - Did not know the double constrictor
Isn't it a clove hitch with an extra turn?
And even more secure by the looks of it !! -
@Huntsman said:
Great contributions everyone - Did not know the double constrictorIsn't it a clove hitch with an extra turn?
And even more secure by the looks of it !!I can see why you would say that, because they are very similar, but there is another key difference.
In the clove hitch the two ends are side-by-side, but in the constrictor knots the ends overlap a d apply pressure to each other.
Maybe the best way is visual. Here is a picture of the clove hitch, single constrictor and double constrictor (L->R) before tightening.

You can see with the constrictor knots, each end is overlapped by the other end where it exits/enters the knot. Because of these overlaps a pull on either end tightens the knot but also presses the opposite end down into the object. The pressure on the opposite end means makes it highly unlikely that the knot will loosen, especially if either end is under tension.
I hope this makes sense, because despite understanding it in my head, I’m not sure I explained it well.
-
Fantastic explanation and examples ....... Thanks SOS :D

Much easier to see with the single constrictor

-
-
OK - I really should post earlier in the week..... Or at least post immediately after I took my photos ..... because.......
I took photos of my Figure of Eight yesterday when I took my Yosemite Bowline piccies - Ready to post today .....
But of course enki
knicked my knot ..... Knot funny >:(Anyway seeing as I had the pics already I will post them and say a few words about the use of the knot.
It's slightly different from Enki's Figure 8 - No bight - But essentially still a double threaded Fig 8.So this is how ***nearly all ***UK crag climbers tie into a rope..... See diagram/piccie.
-
You take the rope and tie your first Fig 8 about 1 metre from the end of the rope
-
You then thread the free end through the waist loop and (very importantly) the groin loop of your climbing harness
-
You then feed the free end back around the Fig 8 following the line of the rope all the way - as you see in the diagram/piccie
-
And probably ...... as always ,,,,,,, finish off with a stopper knot - Which I do not show

Perfect!!
As mentioned earlier this knot takes longer to tie than a Bowline, is way harder to undo under strain ie if you fell on it
But is easier to tie, less chance of a mistake and much easier for your partner to check .......as you can see !!I will say a few more words about the Fig 8 when I make my post for this week!! :o
-
-
I was vaguely worried that the humble Clove Hitch would be overlooked. Yet, it is one of the most fantastic knots ever conceived. From docking freights to securing a truck's load the Clove Hitch is always ready, willing and able!
There is a magical quality to the Clove Hitch: it almost seems too simple to work. Yet...it will hold tons.
Here is a shot from a recent camping trip, a slippery Clove Hitch securing a guy line perfectly:

Looking at the photo, it seems tied a bit sloppily. And it is loaded slightly off to the side. No matter! The Clove Hitch prevails!
I'd put the Clove Hitch up in the "Top Five Essential Knots" to know. No kidding--fantastic knot.

That was going to be my 2nd entry...

-
- The rabbit's hole :)
- The rabbit approaches the hole. :D
- Misses it but sees another one. :-\
- Misses it again. >:(
- One hole capsizes as the fabric of reality folds over itself.

- One hole swallows the other one. :ahhh

-
@Huntsman said:
OK - I really should post earlier in the week..... Or at least post immediately after I took my photos ..... because.......I took photos of my Figure of Eight yesterday when I took my Yosemite Bowline piccies - Ready to post today .....
But of course enki
knicked my knot ..... Knot funny >:(Anyway seeing as I had the pics already I will post them and say a few words about the use of the knot.
It's slightly different from Enki's Figure 8 - No bight - But essentially still a double threaded Fig 8.So this is how ***nearly all ***UK crag climbers tie into a rope..... See diagram/piccie.
- You take the rope and tie your first Fig 8 about 1 metre from the end of the rope
- You then thread the free end through the waist loop and (very importantly) the groin loop of your climbing harness
- You then feed the free end back around the Fig 8 following the line of the rope all the way - as you see in the diagram/piccie
- And probably ...... as always ,,,,,,, finish off with a stopper knot - Which I do not show

Perfect!!
As mentioned earlier this knot takes longer to tie than a Bowline, is way harder to undo under strain ie if you fell on it
But is easier to tie, less chance of a mistake and much easier for your partner to check .......as you can see !!I will say a few more words about the Fig 8 when I make my post for this week!! :o

(I believe the Figure 8 is also stronger than a Bowline. I.e. the knot doesn't weaken the rope as much as a Bowline.)
-
Gordian knot
How to tie it: unknown (at least to me)
How to untie: use a sword (or scissors)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




