EDC Bit Ratchets
-
Thanks!

The humble Mulwark. What a classic! :D -

711L Micro Ratchet
(Can also be found branded by Signet.
Same design as CROM and LaBear, but those have 60 teeth and are t-handle capable)Max torque rating: 30 nm / 22 ft lb
Weight: 19g
Length: 50mm
Head width: 15mm
Head clearance with standard bit: 25.5mm (adds 0.5 mm)
Teeth count: 52
Minimum swing arc: 7°
Bit retention: spring
In-line driver retention: magnet
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $20 alone, $24 with 8 bitsAccessories
The 711L ratchet can be found alone in a tin, or with a bit set for a few dollars more.
Dimensions
The 711L is truly microscopic, at only 50mm long and weighing a measly 19 grams. It has a narrow head, and adds 0.5 mm or less to a bit, depending on the bit.
Bottom right: 711L, Jackly, Tone, Wera, Hazet, Wiha, Stanley, Topeak, BGS, SK11, Klein, PrestacycleTeeth count
Much like the Topeak, Giant, PK Tools, etc, the 711L ratchet has 52 teeth, for 7 degrees minimum swing arc. Just excellent.Bit retention
Bits are held in the ratchet with a spring. The inline driving slot has a magnet. Retention is excellent.Bit compatibility
Stubby bits are not easy to remove from the in-line driving socket.
Standard double-sided bits and Leatherman bits can be used with the ratcheting head, as long as one end is thin enough to clear the hole in the back. Leatherman bits have to be inserted properly, with the spring engaging their retention notches.
Double-sided bits cannot be used in the in-line driver. They do not engage the sides, and thus cannot be turned.
Leatherman bits can be used, but they barely engage the sides and have a lot of play left and right.
Impact bits with the grooved neck do not engage the ratchet spring, so they will have a lot of play back and forth, but they do not fall out.
The double-ended stubby Steinwhale bits are a wonderful companion to this. They can be used in both ends and take very little space.Bits with a more rounded back sit flush with the ratchet head, allowing the clearance to be whatever the bit length is.

Switch action
The 711L has a small -arguably too small- and low-profile switch with good detent, so the action will not get reversed accidentally. The switch tail rests in a scalloped area, which guides the thumb left or right, to make operating the switch easy.Ease of use
Though small, the 711L ratchet retains the features of its kin. Knurled finger wheel, inline bit driver, 52 teeth. The length makes this a two-finger grip. The thin middle makes for a nice place to pinch with a thumb and finger.An extension or bit in the inline driver can be used to increase the length for more comfort and more torque. With a 50mm (2") extension, the 711L will be the same length as the Topeak, Giant, etc. It will perform essentially the same, with the added benefit of having an extension in virtually the same space that the Topeak would occupy on its own. And having an extension as an L configuration makes the 711L even easier to use.
The Steinwhale bits also fit the ratchet and regular extensions. Truly a match made in Heaven.
Construction Quality
Same excellent build quality of its taller siblings. Everything is polished, chamfered, smooth. Tolerances are tight, there is very little wobble in the ratchet head.Portability
Its main feature, the 711L ratchet is the tiniest yet. This is perfect for a keychain, thanks to the hole in the head. It will disappear in any pocket or purse, and can probably be added in any edc kit without the need to remove anything.
This is much slimmer and lighter than the other keychain ratchet already reviewed, the Jackly keychain ratchet, and of higher quality, and of course more expensive.
The tin it comes in can be used as a tiny bit kit. It fits the ratchet and a few bits, although it may rattle a little in a pocket.
Value
When first launched, this was $30 for just the ratchet and tin. It is now $20. It can be found for a few more dollars with bits. Definitely somewhat expensive, but arguably justified for such quality in such a tiny package.Conclusion
This should be familiar to some. It is essentially the Topeak head on the inline driver. It is the tiniest ratchet yet, and just about perfect for a keychain. This is the best option for lightweight edc where every gram counts. Despite its size, it is still a functioning ratchet, and a very good ratchet at that.
Its only drawback would be the limitations that come with a tool this small. This may be too small to manipulate effectively for people with larger hands, but this can be easily solved with a long bit or an extension in the inline driver.
Of course, this may seem somewhat expensive to some, especially when compared to ratchets with the same head and construction, like the PK Tools, Topeak, etc. If size limits allow for it, maybe a Topeak/Granite/Giant ratchet set would make more sense. Still, for what it is, the 711L ratchet is still an attractive option. It has gotten more affordable since launch, it will occupy the least amount of space from the ratchets we have seen so far, and it works just as well as larger ratchets.
Pros
-Perfect keychain ratchet; lightweight, short, hole in the head for attaching clip.
-Retains features of similar ratchets (inline driver, 52 teeth, knurled wheel, hole in head, great quality).
-Can be found from different brands, with bit kits and cases.
-Has an inline driver:
-Can drive inline.
-Can store a bit while on a keychain.
-Can store an extension or long bit and be the same length as the Topeak.Cons
-None.If you liked this ratchet, also check out:
-
I guess this could fit under this subject, pretty interesting, the “T” shape handles pull off and can be used as extensions either way, the same with the drive, so if you want a long ratchet, or if you want something small and will fit you can just use the main ratchet,, I still haven’t used it but I thought it was pretty cool..
JR
-
Zoyo Sports ratchet just in.
Comes with a drawstring bag and a holder.
Quite interesting. It's the length of the Topeak, but thicker, ever thicker than the Prestacycle ratchet.

-
LaBear folding ratchet
Engineer PZ-54
Blackburn Big Switch ratchet

-
Topeak, Blackburn, Zoyo, Prestacycle
The first three are the same length.
The Blackburn is the same thickness as the Prestacycle and has the same head as the Topeak.
The Zoyo is the thickest and has the same head thickness and teeth count as the Prestacycle (no T-handle capability)
-
This thread never disappoints

-
Brand new from 711L.
Imagine this with an inline driver. Mini flexhead t-handle.

Why is this t-handle? It doesn't have an inline driver. Why be T-handle?

-
Leatherman ratchet is in!

-
@ReamerPunch said:
Leatherman ratchet is in!Nice, i will eagerly wait your review on it. I havent pulled trigger to buy it yet since its bit pricey here and cant find justification to buy one cause i have Vic ratchet what can do most of my jobs.
-
@Antti Lammi said:
Nice, i will eagerly wait your review on it. I havent pulled trigger to buy it yet since its bit pricey here and cant find justification to buy one cause i have Vic ratchet what can do most of my jobs.I have written most of the review on it, and I can tell you now that your post sums the Leatherman ratchet adapter nicely. It is expensive, offers little justification to buy, and other regular right-angle bit ratchets cover most needs. I''ll take photos and post the review soon.
-
Wiha has many GoBox sets. Standard for $30.


-
There is a swivel-head with a fixed inline driver. So this is better than the Titan swivel-head. Branded AP (Astro Products).

-
Topeak has a different ratchet, but it comes with less and costs more than the regular one.


-
-

Hazet 2021SA Advent Calendar 2021 set / Hazet 863MHP ratchet
Warranty: Lifetime
Weight: 99g or 3.5oz
Set weight: 498g or 17.5oz
Length: 89mm
Head width: 21mm
Head clearance with standard bit: 26mm (adds 1mm)
Teeth count: 90
Minimum swing arc: 4°
Bit retention: spring
In-line driver retention: spring
Extension retention: magnet
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $186 with 18 bits, extension, 3 sockets, 3 wrench ends, and caseSockets (six-point): 8, 10, 13
Wrench ends: 8, 10, 13
Bits:
Phillips #1, #2,
Allen 3, 4, 5, 6
Torx 10, 15, 20, 25, 30, 40
Slotted 1.5, 4, 6.5
Square socket adapterAccessories
The Hazet 2021 Advent Calendar set contains an extension, socket adapter, three metric sockets, three wrench ends, and 17 bits.
All components are marked with the Hazet logo. The extension is a common impact magnetic extension.
The bits are color-coded.
The sockets have a double finish, dull and satin, divided by a knurled ring.
The three wrench ends are essentially half a wrench, with a 1/4" hex end. They fit into the ratchet or extension for added length. This is why the inline driver is so robust.The case is what Hazet calls a Smart Case. The base and top are hard plastic covered in a rubberized material, which provides traction.
The front of the lid displays the contents in silhouette with their respective sizes.
It has magnetic closure and all internals are held in the lid. While the contents survive the upside-down test, the case itself does not. The magnetic closure is not strong enough for how heavy the contents are, and if grabbed by the bottom half, the lid with all contents will swing open. Of course it can be treated as a conventional case, placing it contents-down.The rubberized part runs the full length of the base and lid, and acts like a smartphone wallet. The double-hinged rubber backing allows the lid to interlock at an angle with the base, to have the contents displayed in full view, while the base acts as a tray for parts.

Dimensions
At 89mm long, the Hazet ratchet is rather short. The head is 21mm, definitely on the wide side.
Bottom right: 711L, Jackly, Tone, Wera, Hazet, Wiha, Stanley, Topeak, BGS, SK11, Klein, PrestacycleTeeth Count
At 90 teeth, the Hazet ratchet shares the top of the list with the Titan swivel-head. It requires only 4 degrees of minimum swing arc, to engage a tooth and turn a fastener.Bit Retention
The ratchet has ring springs for the ratcheting end and inline driver. Retention is firm, but not over the top. Even stubby bits can be removed easily from both ends. The extension has a magnet that is a bit stronger than the springs.Bit compatibility
The ratcheting end has a smaller hole compared to other ratchets, like the Wera, Topeak, Ares, etc. This limits the amount of double-ended bits that can be used, because one end has to be very thin in order to use the other end. Stubby bits can be used just like regular bits.The inline driver is more accommodating. The 1/4" depth is excellent for regular and stubby bits. The interesting feature is that the 1/4" hole transitions to a 6mm hole, allowing for double-ended bits to also fit in perfectly. Leatherman bits work properly. Standard double-ended bits with ball detent also work fine, and even though the ball detent will not engage, the inline driver's ring spring will.
Even long, double-ended impact bits fit perfectly in the inline driver. The only other ratchet that can use these bits in the inline driver is the Victorinox ratchet.The extension is not deep enough for double-ended bits but stubby bits can be removed with no issue.

Switch action
The Hazet ratchet switch is quite larger compared to similar ratchets. The end of the switch protrudes upwards ever so slightly and is very easy to use, while tucked safely behind the head.Ease of use
With 90 teeth, the Hazet can work even in very confined spaces. The inline driver is also very useful and extremely robust, since it has to double as the wrench end extension. The thin neck and wide ends allow for a comfortable grip, locking the thumb and fingers around the handle. The switch is very easy to use as well.
The wrench ends can be used to some extent as stubby wrenches.
A knurled wheel would have been a nice feature to have, especially considering how much back drag this ratchet has. The resistance of the ratchet head when turning to engage a tooth is significant, and much more than any other ratchet so far. This means that for the ratchet to actually start ratcheting, the fastener has to be tighter compared to other ratchets.
The case can stand at an angle, making it a bit easier to identify and remove something. The base acts as a tray for spare parts, fasteners, etc.
Construction Quality
The Hazet ratchet is very well-made. The finish is consistent. The ratcheting action is smooth. Bits go in and out beautifully. The ratcheting mechanism has no gaps in the frame. The switch has no wobble in the frame. It is worth noting that this ratchet head is used for other models by Hazet, and a repair kit is available, as well as a 1/4" square drive.
The sockets and bits are also flawless. The wrench ends are a little inconsistent. The 10mm especially seems to be the worst, with quite obvious grind marks on the outer sides of the jaws.Portability
The hole in the head allows the ratchet to be clipped to other gear with a quick-release clip or thin carabiner. The inline driver makes the ratchet a little thicker compared to similar ratchets, but it still fits in multi-tool sheath side-sleeves, pen slots, and edc pouches. Being 89mm long, the Hazet ratchet can fit comfortably in an Altoids tin. At 99 grams, it is the heaviest ratchet yet. If you are looking for a lightweight option, this is not it.
The case is quite bulky and not suitable for edc. It will fit in a cargo pocket, but it weighs half a kilo or over a pound, so it will pull your pants down.
Value
Being a limited release and long discontinued complicates things. It is a premium set, with a good selection of accessories. The ratchet is well-made, it has 90 teeth, a nice inline driver, it is heavy duty. The case has some nice features as well. Hazet offers a lifetime warranty, so if you do manage to find this, you will be set.Conclusion
The Hazet 2021SA set is definitely interesting. It is by far the most expensive and hardest to find. The ratchet and case have some nice features. The set is extensive. It is high quality and has a lifetime warranty.It would not make much sense not to recommend the set. It is a very nice ratchet, with 90 teeth, great quality, a lifetime warranty, a nice inline driver, and extremely heavy-duty, probably the most rugged so far, and definitely the most robust inline driver in this thread.
It would not make much sense to recommend it either. It only came as part of the 2021 Advent Calendar set. The ratchet did not come in any other set or sold separately. The set has been discontinued for a long time, and no new stock will exist. It does appear to be available from Japan as unsold, old stock, so not impossible to find, but there are some hoops to be jumped through.
If you do find it, it may be all you need. Until you do, maybe get something else.

Pros
-Lifetime warranty.
-High quality.
-Heavy duty.
-90 teeth for only 4° minimum swing arc.
-Comprehensive set.
-Versatile case.Cons
-Expensive, limited release, and discontinued.
-Heavy ratchet and set.
-The socket and wrench sizes are the same.
-Quite high back drag.
-Magnetic closure on the case is not strong enough to keep it closed firmly.If you liked this ratchet, also check out:
-

Leatherman Ratchet Adapter
Warranty: 2 years
Max torque rating: 20 Nm / 15 ft lb
Weight: 35g
Length: 81mm
Head width: 15mm
Teeth count: 48
Minimum swing arc: 9.5°
Bit retention: magnet
Handle material: Chromium-Vanadium steel
Price: $43Accessories
The Leatherman ratcheting adapter comes with nothing.
Dimensions
At 81 mm long, this is not much longer than regular bit extensions. Due to the ratchet collar, this is a little thicker in the middle.
Bottom right: LaBear Folding, 711L, Jackly, Leatherman, Ares, Wera, Tone, Wiha, Sharden, Bosch, Topeak, Blackburn, Zoyo, Victorinox, CyclingDeal, PrestaCycleTeeth Count
With 48 teeth, this has a 9.5 degree minimum arc, but this is irrelevant as it is a ratcheting extension, and not a right-angle ratchet.Bit Retention
Bits are held in by a magnet. The magnet strength is above average.Bit compatibility
The socket is deep to specifically accommodate Leatherman bits. It can also use regular double-ended bits; the ball bearing will not engage, but the magnet is fine.
The socket is too deep for stubby bits.
Switch action
The Leatherman ratchet adapter has a collar to change positions. This is very stiff, and although the surface is ridged for traction, it is still very slippery.Ease of use
The Leatherman ratchet adapter was made to be an accessory of Leatherman tools. It fits in the flattened bit slot. It can use Leatherman bits with no issues. It can also use standard bits, and fits in regular bit drivers. It will add an inline ratcheting capability to regular driver handles, while also act as a regular extension, in the locked position.There are some issues with this design. Being an extension, it still requires a tool for a handle. Using it on its own is not easy. It can be done to get a screw started, but to properly tighten a loose screw or loosen a tight screw, a handle will be needed for leverage.
Changing direction is not easy. The collar that twists to change direction is very tight, and at the same time quite slippery.
The extension does not have the retention notches found on regular extensions and even on Leatherman bits. It has no notches at all, and Leatherman tools just hold it by friction.
Also, bit clearance may be an issue. This was a major point taken into consideration for all ratchets so far. Some ratchets add no length to a bit, others add a millimeter or two, or five, etc. Even with a handle that adds no length to the Leatherman adapter, it is still 81mm long. The worse bit clearance for a ratchet was the Titan swivel head, which added 13mm to a bit's length. Well, the Leatherman adapter adds 67mm. This is not low-profile by any stretch.
The weak-spot of the male end of the ratchet adapter could just as easily not be present at all, if the hex just continued all the way to the base. This design choice may also create an issue with compatibility with certain bit drivers. The ratchet adapter male end's hex bottlenecks into the base, with about 5 mm of no hex. If you use a thin tool as a handle for this, like the PocketWrench II or a One-Piece Tool, the male end of the ratchet adapter will slide all the way through the hex hole, and not even engage properly.

Construction Quality
Something seems to be amiss with construction quality. The ratcheting action is crunchy when tightening a fastener. When loosening it is smooth. In the locked position, the bit holder has quite a lot of play.The finish is consistent and the Leatherman logo is etched perfectly on the stem, but appearance matters little, when construction and therefore performance take a hit.
Portability
This fits snugly in a Leatherman case side-sleeve, Altoids tin, edc pouch, or even a pen sleeve. It weighs only 35 grams, so it is rather lightweight. No carrying features exist on this, no lanyard hole, no split-ring.
Value
At $43 when in stock, this costs a fair amount, more than most ratchets. More than ratchets with cases, bit sets, extensions, sockets. More than ratchets with inline drivers, knurled wheels, flex-heads, higher teeth counts, no bit clearance addition. More than ratchets with greater durability, excellent ergonomics, high quality, lifetime warranty.Conclusion
If you edc a Leatherman tool with the bit driver, like a Wave, Surge, etc, and you find it awkward to drive fasteners, then the ratcheting extension is arguably better than a regular extension. At the same time, a regular bit ratchet is arguably better than a ratcheting extension. Comparing this to bit ratchets may seem flawed, as this is not a bit ratchet. It may also seem one-sided, because it is. The benefits to having this over a right-angle ratchet seem few. For pairing with a Leatherman Wave/Charge/Surge, a small bit ratchet is still easier to use, plus it allows the freedom to carry tools that do not have a bit driver, which this ratchet needs.The Leatherman ratchet adapter is not without value. It is quite neat to attach it to all sorts of handles and ratchet away. Still, all ratchets so far were their own handles and offered more. In some cases, much, much more. With some ratchets we have seen, I had trouble finding any cons to list, and with a few, indeed no cons were listed. With the Leatherman ratchet adapter, this is not the case. There are just too many issues with this, and the price seems to highlight them all. Even if it was of exceptional build quality, which it is not, it is too expensive. Even if it had a lifetime warranty, which it does not, it is expensive. Compared to every ratchet we have seen, and what they had to offer, this is expensive. For what this costs, you can get almost any bit ratchet so far, with change. The PrestaCycle T-handle set with flat wallet is now $35, and you get a comprehensive set for your ratchet needs, plus lifetime warranty. The Blackburn Big Switch comes with 9 long bits, chain-breaker, wallet, and lifetime warranty and costs $38, no additional handle needed. Wiha, Tone, Topeak, Victorinox, Granite, Icon, there are lots of good quality sets available. That is what I would recommend over the Leatherman ratchet adapter.
If you were thinking of getting it and this review made you unsure, maybe get an inexpensive flat ratchet, like the Mulwark, SK11, Vessel, etc, or even a nicer one with lifetime warranty (Victorinox, Blackburn, Wera, PrestaCycle, Granite). Every time you cannot get something done with it but the ratcheting adapter could have done, write it down. If instances keep increasing, then by all means, go for the adapter because you need it. Otherwise, a right-angle ratchet was all you needed, and you saved yourself some money.

Pros
-Inline ratcheting action:
-Teeth count and minimum arc are irrelevant.
-Improved reach.
-Increases versatility of non-ratcheting inline, right-angle, and T-handle drivers.Cons
-Expensive and comes with nothing else.
-Warranty is only two years.
-Collar is very stiff and slippery.
-Ratchet action is sticky when tightening.
-Requires driver for a handle.
-Compared to this, all ratchets so far can be considered low-profile.Looking for an edc ratchet? Check these:
-
The Klein reversible nut driver is perfect for driving tiny bits.
This is the SK11 ultra stubby bit set. The bits are only 12mm long.
The Klein drives them fine. Pull the socket out slightly to make it a hair deeper for the bits. To extract the bit, just push the socket in. Perfect for tiny bits. The 711L double function extension would also be ok I think. I had also ordered a Stanley nut driver but they ran out so I only got the Klein.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



















































