And so it begins.... (My adventures into Alox!)
-
@Syph007 said:
OMG yes! I didn't have any problems drilling out the springs or parts to 1/8 inch. The tool components for alox SAKS start at 3mm anyhow, so not much material to remove. Small price to pay for easy assembly and servicing!The only thing I'm wishing is for some screws that looked more like rivets. Maybe the button heads would look better. I could hit the alox scales with a milling bit to square the hole bottoms... hmmm
Mate I just saw this :o
.I am interested to hear how you did drill out the holes on the smaller components
, I would of thought getting the smaller parts secured & drilled out would of been a bit of a head ache
.Urban Pioneer
, If you could sneak a nail file in there some how

Great work mate

-
@MultiMat said:
I am interested to hear how you did drill out the holes on the smaller components
, I would of thought getting the smaller parts secured & drilled out would of been a bit of a head ache
.Its actually one of the easier steps. The hardest is deburring and polishing the inside of the holes after drilling.
I wear kevlar shop gloves since I cut myself too much, so for drilling all I do is dip the part in cutting oil, put a little oil on the carbide drill bit, then hold the part with my gloved hand and use a drill press to punch through the hole. Not having it clamped down works better for me since it kind of auto centers that way and you can 'feel' if its cutting right. It takes maybe 15 seconds to drill out a part, but more like 15 minutes to polish after.
I'm working on some wackier combinations now, but over all I love the threaded pivot pin system!
:D
-
Wow holding the part just in your hand :o :o 8) 8) 8).
No putting holes in those fancy gloves
:D :D , you do have some fancy fasteners you could use doing 'Orthopaedic' repairs if your drill misses :P :D :D.Great work again mate 8) 8) 8)
Keen to see the wackie SAKies you have planned
:D -
A 2 flute carbide end mill works really good ;).
-
@tattoosteve99 said:
A 2 flute carbide end mill works really good ;).I tried an end mill on a spring once, but I didn't have it dead on straight and the hole was slightly off, so it's easier for me to use a regular spade bit. I haven't had a problem at all with that style.
-
@Syph007 said:
I've gone through more screw variations than I want to admit, but I am 100% happy with these flathead variety. They fit like a glove in the end holes so I only need to kiss the center hole with a drill bit to get the screw to fit there. Since hardly any drilling needed to be done, the scales have the maximum amount of pivot extending into them, for maximum strength. They are also nicely flush with the surface.Those screw heads look great! Are you polishing them? I chuck a pin in a Dremel collet and screw the screws into it and spin them full speed while hitting them with 600 grit paper to take the machine marks out, then some Flitz on a rag and they look like chrome.
-
I've gone through more screw variations than I want to admit, but I am 100% happy with these flathead variety. They fit like a glove in the end holes so I only need to kiss the center hole with a drill bit to get the screw to fit there. Since hardly any drilling needed to be done, the scales have the maximum amount of pivot extending into them, for maximum strength. They are also nicely flush with the surface.
Those screw heads look great! Are you polishing them? I chuck a pin in a Dremel collet and screw the screws into it and spin them full speed while hitting them with 600 grit paper to take the machine marks out, then some Flitz on a rag and they look like chrome.
I did hit those with a buffing wheel and stainless polish, and they got pretty shiny. Putting them in a dremel would have been easier than the way I did it. I held each screw with my fingers and hit with polishing wheel in a dremel! LOL I wont be showing my son my techniques. I seem to still have freakishly strong fingers though from my years of rock climbing, so its just easier for me to hold things. I dont have a problem bending the sak backsprings by hand when I assemble. I just push hard and wiggle the part home. I thought Id have to make a jig for that, but havent had to at all.
The other screws I had were the same profile, but these have larger hex bit, and they seem to be more visually appealing, at least to me. Of course I have 200 of the other kind still... :D Also many in black, but they dont look right.
-
The fit & finish on that Urban Pioneer is just amazing!
Jeff
-
@jds1 said:
The fit & finish on that Urban Pioneer is just amazing!Jeff
Thanks! It's taken me a bit of trial and error to perfect the drilling of the outer scales so I don't mar them at all. I'm currently rebuilding my EDC sak now out to 4 layers.
- 91mm combo tool / blade
- pliers
- cybertool bit driver
- scissors
I keep refining what I want to have as a simple daily needs type sak. The only thing Id still like to add is a pen and tweezers, not so interested in the tootpick, but I need a pen and tweezers often.
-
that is nearly identical to the mod I've asked Steve to make for me, only without the combo tool and blade, and instead having an awl and file/metal saw in their place. Otherwise identical 4 layer alox SAK (if the bit driver can be fit to the alox frame).
-
@Raukodur said:
Otherwise identical 4 layer alox SAK (if the bit driver can be fit to the alox frame).I'm going to make it fit somehow. I'm not in love with the plastic bit holder, that's going to get remade out of anything nicer than plastic, probably aluminum, Ti if im feeling richer. I dont have the driver part yet though, its en route so I cant test yet to see how it fits.
What I found when I swapped the standard opener layer for the combo too, i missed having the driver ends of those tools. But if I add in the bit driver layer, that solves that problem, and the combo tool becomes mostly just an opener.
-
well, I'm a UK user so knife is problematic, and I don't use openers and the bit driver replaces the bit ends as you said, so no need for knives or openers. The awl and file/metal saw are much more useful tools for me, hopefully both can be fit into a single layer.
If that plastic bit holder was metal, that would be pretty sweet. An entirely stainless steel SAK would be quite something to behold, liners and all. Although would take up the weight a fair bit.
-
@Raukodur said:
If that plastic bit holder was metal, that would be pretty sweet. An entirely stainless steel SAK would be quite something to behold, liners and all. Although would take up the weight a fair bit.Ya I think all parts that can be made for Titanium for weight, and then the standard SAK components. Id LOVE that.. but a sheet of thick titanium is quite an investment. :D But a man can dream.
-
Let me know how thick that bit holder is. I have small chunks of 1/4" and 3/16" titanium that I'd sent you just to see you try it. Also some 1/8" CF scrap that might work better because you could carve it clamshell style and sandwich the halves together. Does anybody have a picture of a naked bit holder? I've always wanted to look up one's skirt.
-
@bushidomosquito said:
Let me know how thick that bit holder is. I have small chunks of 1/4" and 3/16" titanium that I'd sent you just to see you try it. Also some 1/8" CF scrap that might work better because you could carve it clamshell style and sandwich the halves together. Does anybody have a picture of a naked bit holder? I've always wanted to look up one's skirt.I have one attached to a cybertool, I'll break out the calipers and camera after I get this baby to fall asleep! :D The wife is at work tonight.
-
Let me know how thick that bit holder is. I have small chunks of 1/4" and 3/16" titanium that I'd sent you just to see you try it. Also some 1/8" CF scrap that might work better because you could carve it clamshell style and sandwich the halves together. Does anybody have a picture of a naked bit holder? I've always wanted to look up one's skirt.
I have one attached to a cybertool, I'll break out the calipers and camera after I get this baby to fall asleep! :D The wife is at work tonight.
I snapped some good pics. The part is almost exactly 0.250 thick. Roughly 3/4 inch by 2 1/4. It has a seam around it, you can see it was made by pressing 2 parts together.
Anyways here are the pics.... Id love to remake in Ti.. oh boy!
By the way, this cybertool has the thickest liners ive ever seen on a 91mm SAK.. 0.050! Its the butter soft aluminum though, so I think they beefed up thickness for this tool. Yet another benefit if remade with stronger thinner liners, the tool would be thinner!




-
Oh this will be VERY Exciting... definetly one of my goals to have a Alox Cybertool!
The only thing with a titanium bit holder is I wonder if the bits would kind of stick in there too tightly, maybe since the bits would be enough smaller than their sockets because of the bearing that would not be a problem. Titanium seems tough to get right when threads or friction fit is required.
-
@ICanFixThat said:
Oh this will be VERY Exciting... definetly one of my goals to have a Alox Cybertool!The only thing with a titanium bit holder is I wonder if the bits would kind of stick in there too tightly, maybe since the bits would be enough smaller than their sockets because of the bearing that would not be a problem. Titanium seems tough to get right when threads or friction fit is required.
Ya I dont think a friction fit would work.. maybe tiny leaf springs... hmm. I'll have to think about it, but there's gotta be a way.
-
The driver has magnetic retention right? Why not the bit holder? Teeny tiny neodymium magnets.
http://www.kjmagnetics.com/proddetail.asp?prod=DH101A titanium bit holder is totally doable. I'd go with multi layered construction riveted together. The slots could be cut into a single piece, retention magnet holes drilled and the outer layers riveted on. I really like eliminating SAK plastic.
-
@bushidomosquito said:
The driver has magnetic retention right? Why not the bit holder? Teeny tiny neodymium magnets.
http://www.kjmagnetics.com/proddetail.asp?prod=DH101A titanium bit holder is totally doable. I'd go with multi layered construction riveted together. The slots could be cut into a single piece, retention magnet holes drilled and the outer layers riveted on. I really like eliminating SAK plastic.
Magnets! Yes that would work. Each bit though does have the spring loaded steel ball in the center, so a corresponding tiny indent ring in each bit holder slot would work too.
This SAK plastic is really low quality on the holder, so an upgrade to metal would be wonderful. The design would have to be altered anyhow to fit in an alox frame as currently this slots into a gap in the springs, and on my alox model there would be no gap as the springs would extent the length of the knife.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login