And so it begins.... (My adventures into Alox!)
-
@tattoosteve99 said:
Nice work. Now all you need to do is figure out file work

Id have to study at the Sidhartha school of filework for that! :D Or maybe make some kind of file holding jig to get the spacing and angle right... hmmm maybe....
-
Nice job! good little configuration for a clip pocket knife! JR
-
I saw your avatar and headed straight here to admire this masterpiece in its full splendor.
Excellent work. 


-
Today I went back to working on my 84mm pioneer with converted 91mm scissors. I posted these pics in another thread, but will repost here for consistency.
These are the modifications I did to the old style 91mm scissors and 91mm backspring to fit on the 84mm frame.


And here is the rough fit up to test it all together. I was testing the look of some designer low profile screws on the end pivots, still not sure if I love them or not.


The full cutting blade length of the scissors was preserved but I did have to nip a bit off the handle part. The part of the awl that rides on the backspring will need to be re-angled to get the awl to point further down and rest on the scale as well.

Here you can see the scissor rest needs a bit more shaved off to let the scissors go just a bit lower. Very close to working.

The scissor snap is perfect so I'm excited to finish this little gem. See what you made me do Victorinox? Would it really be that hard to keep making 84mm scissors???

-
Nice job Syph007.
So the detached piece from the scissor spring is not attached in place, but is held in place by the two matching flats and the pivot?
Leadfoot
-
@Leadfoot said:
Nice job Syph007.So the detached piece from the scissor spring is not attached in place, but is held in place by the two matching flats and the pivot?
Leadfoot
That's correct. I've done that before myself. It works perfectly btw. Not intending to intrude here syph just trying to help.
-
@Leadfoot said:
Nice job Syph007.So the detached piece from the scissor spring is not attached in place, but is held in place by the two matching flats and the pivot?
Leadfoot
Yup it's under tension so it doesn't move at all. I make my scissor rests for 93mm similarly.
I got some 12 Gauge (0.105") stainless 304 that I will use now since it isn't hardened like a SAK spring it will be easier to work. The rest also doesn't need to be spring tempered, so next time I will just chop off the springy part I need and make the rest out of non tempered stainless.
-
Nice way of adding a scissors and looks good too.
Will add this to my growing list of good ideas.
Leadfoot
-
Well thanks to you I was almost late for work this morning. I couldn't stop reading this thread!
Very interesting.
-
@BlueDot said:
Well thanks to you I was almost late for work this morning. I couldn't stop reading this thread!Very interesting.
lol.. apologies to your work, but I've done the same reading threads in this section, so I know how it goes!
Nothing too exciting to look at yet, but this is what I spent all my free time doing this weekend. Stripped naked SAK scales.. bare of all anodizing!

I had to track down 100% pure lye and strip these in the backyard. Nasty nasty stuff, it was boiling away like a witches cauldron. I got the ratio mixed so that each scale only needs about a 30 second dip and when I cant see any more red on the shield, it's done.
My first run I let the electroplater guy strip for me (lol that sounds odd) and some of the red remained behind, so I wanted to do the prep this time to be sure of what I get. If the cost isn't too high this will get done in 3 colors HAIII black/red/orange... if it costs too much than just 2 colors either black and red, or black and orange. I'm dropping them off in the morning and I hope he can be done soon since I'm super anxious to put some colored ones together!
-
orange me thinks orange!
but if i can be really bold go for something like suzuki RM yellow. Stand out from the crowd :D
-
I'm waiting with bated breath.

-
Still waiting to hear about my anodizing.... I really hope he's done by the weekend!
Here is a test mock up of the part I made in my templaing thread. This is a 0.105" thick rest made from 304 stainless, with super beefy keyring attachment.
This is a prototype test fit only, it still needs some adjustment, but it's darn close.


I think it looks pretty decent.



-
very nice!! you are getting serious in this, congrats!
btw i really like that golden pin, it looks very cool
. -
@Sidhartha said:
very nice!! you are getting serious in this, congrats!btw i really like that golden pin, it looks very cool
.lol it was all i had on hand to test fit... :D
-
That looks great. So much sturdier than the spacer keyring and in the Urban Pioneer it puts the keyring right in the center layer. Now you just have to rout out a hundred or so and send them to me so I can tumble polish them.

-
very nice!! you are getting serious in this, congrats!
btw i really like that golden pin, it looks very cool
.lol it was all i had on hand to test fit... :D
i have done the same a few times :D
-
@bushidomosquito said:
That looks great. So much sturdier than the spacer keyring and in the Urban Pioneer it puts the keyring right in the center layer. Now you just have to rout out a hundred or so and send them to me so I can tumble polish them.
Or waterjet!! :D I don't have a band saw, so I have been hack sawing them to rough out, then filing to get close, then routing. Probably about 30 minutes each, so 100 wont happen too quickly...
-
Happy days are here, we have colors!!! They called just as I was leaving the office so I grabbed them on the way home. They were out of orange dye so I ended up getting hard anodized black, red and blue!




Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
