The Splash - LM Squirt Mod
-
Long after they have made a multi-tool for each person on earth, the collectors and modders will continue to fuel demand...
-
Did some planning today, taking a mental break from Skinth.
From what I gathered this is the load out.
A Layer 1 (outside):
-PE Blade
B Layer 1 (outside):
-3D Phillips/Flat DriverA Layer 2 (inside):
-Nail File
B Layer 2 (inside):
-2D phillips/Awl
C Layer 1 (outside):
-SE Blade
D Layer 1 (outside):
-ScissorsC Layer 2 (inside)
-?????!!!!
D Layer 2 (inside)
-Eyeglass Driver/Tweezers--
So after planning. I notice...wait a minute! Even with ALL of the tools in one Squirt from 3 squirts...there's still a blank outside opening slot!!! What to do?!
A package opener? The standard file? a wire stripper? a warney blade? gut hook? Another pair of scissors? Staple pry bar?
AHHHHH MY BRAIN IS NOT WORKING!
-
It's all looking good mate, but a few thoughts if I may ...
-
The blade length seems too short to bother with serrations for me - are you sure it'll be worth the effort (if you drop that you're on an even tool count)
-
If keeping the SE blade, I think a package opener would round things off nicely
-
How are you overcoming the nail nick issue? The outer tools obscuring the inner tools - there isn't enough clearance on the backsprings for the pliers to reverse them either
-
-
@50ft-trad said:
It's all looking good mate, but a few thoughts if I may ...- The blade length seems too short to bother with serrations for me - are you sure it'll be worth the effort (if you drop that you're on an even tool count)
- If keeping the SE blade, I think a package opener would round things off nicely
- How are you overcoming the nail nick issue? The outer tools obscuring the inner tools - there isn't enough clearance on the backsprings for the pliers to reverse them either
I am going to give it a go anyways, the SE I made already is too aggressive. I am going to see about making a more gentle curved one. I've never been one to shy away from a challenge.
I was thinking of taking a Swann-Morton scalpel blade holder and adapting it to the last spot. I do a lot of paper craft and detail work and having one on the go would be pretty neat. Also, the replaceable blades would be nice too. Failing that, I think a super pointy, Exacto shaped blade would be good a substitute if it wouldn't fit.
All it would take would be a new profile on one of the blades and then a chisel grind with my Lansky sharpner.
As Evilolive has demonstrated when he assembled his, there is room for finger nails to get in there, it'll be SAK like, but still doable.
Here's the pics from his thread:


You'll notice that there is lots of space for deployment. The sandwiched chassis and spaces will work...I hope :)
-
how much bigger is it? -
Ah, I see - looks like the layers are well spaced. I'd got a more compact vision in my minds eye :)
-
More parts came in today.
A really worn E4 and a couple of P4's. The grey p4 will be the one to be disassembled.
I opened the package with a very generous early birthday gift from Cornholio, a gerber g10 EAB ;)

I also ordered a couple of Swann-Morton scalpel holders (steel ones) and I am going to try to shape and fit it into the extra blade slot I discovered.
-
I like the idea of sharp replaceable blades


-
Looking forward on seeing how this mod progresses.

BTW. How do you like the form factor of the EAB lite compared to the original one?
-
I like how you alway come up with new ideas.
Judging from the size i imagine the EAB to be, the Squirt seems to be tiny.
Would you mind taking one of the next pics with a Sak as a reference? Or maybe a freehand, just for giggles ;-)If one of the Squirts (maybe one with the wire stripper head?) ends up unharmed, i might feel the need to pester you to trade me one...
Until then:

-
@lowtech said:
I like how you alway come up with new ideas.
Judging from the size i imagine the EAB to be, the Squirt seems to be tiny.
Would you mind taking one of the next pics with a Sak as a reference? Or maybe a freehand, just for giggles ;-)If one of the Squirts (maybe one with the wire stripper head?) ends up unharmed, i might feel the need to pester you to trade me one...
Until then:

I know I won't be screwing with a couple of more mint e4's.
I'll take rally when this mod gets done. The pivots, blade holders and the s4's need to come in before I get going on this :)
-
Screw this, I did it, I am going to try to make a big awl for one of the "big tools", in place of the mini awl will be this (hopefully). The steel from a Surge removable saw blade should be fine steel for the "big" awl.
Ground down the E4 (which is narrower at the tip) into a stubby package opener. Not sure if I am am 100% on board with this, but it seems to work. I call it the push and pull package opener.




Why push and pull? Push in the sharp tip to pierce the plastic, then pull to slide the cutting edge. Leatherman fans will know that is a BO Rebar being opened up.



So this calls a for a new tool load out.
Big tools
- PE blade
- Scalpel
- Scissors
- Big awl
- Nail file
Small tools
6. 3d Philips
7. 2d Phillips
8. Eyeglass driver
9. Flat bit/bottle opener
10. Push&Pull package opener
11. Tweezers -
I hope to see those ruler scales soon, personally that's the part of this mod that interests me the most. I feel that the pivot/rivets on the squirts' scales look a little messed up if you look closely.
-
@scorpion008 said:
I hope to see those ruler scales soon, personally that's the part of this mod that interests me the most. I feel that the pivot/rivets on the squirts' scales look a little messed up if you look closely.I'll be tackling those tomorrow. For now...
Did some prep work, took apart a E4, P4 and a PS4' salvaged the parts I needed, all I need is the nail file from the S4 and the pivots.

I took the oldest chassis, from the E4, and cut them in half to make the new layers back springs. Cleaning them up with the same end mill that I used to cut them in half. I may adjust them later so I can make room for accessing the nail nicks.

These pics are kind of a nice way to illustrate the complexity of the Squirt chassis.



Assembling this guy will be a bit of a challenge, I'll have to make a diagram of what part goes in what order.

So there we are, two inside chassis, and 4 back spring layers.

-
Some early morning measuring.
Stacking the tools, the whole assembly without the scales and the 4 layers measure .52". This means I have to either splice two pivots together or make 4 really small spacers. I am inclined to make spacers because the Squirt doesn't take a lot of torque like its bigger brothers, I don't need it to be rock solid. Also, the spacers will be used mainly to align the new ruler scales.

Here you can see two blades on the top to layers and 2 driver tools on the bottom layers. The .5" pivots should at least touch all of them.

Here are the ruler I plan to use for the scales. One side for CM's

And one for inches.

I should be able to get 4.5" of measuring might! They will also take up a nice polish being stainless.

I MAY run into some problems with the scissors. Most of the tools are 1/16" so stacking them in pairs would result in an even stack but the scissors are 3/32 together (scissor and back spring). leatherman combatted this with a special scale and a plastic spacer. When closed the PS4 looks even but it's all the scale, I'll have to use washers to even out the layers.

-
Really hoping this will be a success, and then you will decide you don't actually want it, and sell it to me :D
-
Another teaser pic.

I may go whole hog and go 6 layers.
-
@Metropolicity said:
Another teaser pic.Yeah! Take it all off!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login