Wanted: Detailed Diagram of the 91mm Plus Scales
-
@lowtech said:
Regarding the Vic Logo pins, I dare say they will be too big for the scales, the backside clips are typically somewhere between 12-15 mm (roughly 1/2 inch) and are totally covered by the pin.Maybe you can take out the inlaid logo of some Cellidor scales or cut out the hot stamped logo of a set of scales and lay that in.
Will look around. Don't really need a logo. Don't have anything that small that looks good. Have committed with the wood. Can always add a logo some other time.
Wonder if Victorinox had the idea of hiding a small sharpening slip-stone into that scale recess?
-
Talking of logos for wooden scales...
This is a bit of an experiment testing a couple of things. Firstly to see how an "Ivory" cross inlayed into the wood looks and how easy the Tagua nut "vegetable ivory" is to work with and how well it wears.
I will finish these to fit a Recruit and give it a bit of pocket time with flashlight, keys and change for company.I think it will look pretty schmick myself.

-
I like it

Bone and copper cross:
-
@PTRSAK said:
Talking of logos for wooden scales...
This is a bit of an experiment testing a couple of things. Firstly to see how an "Ivory" cross inlayed into the wood looks and how easy the Tagua nut "vegetable ivory" is to work with and how well it wears.
I will finish these to fit a Recruit and give it a bit of pocket time with flashlight, keys and change for company.I think it will look pretty schmick myself.

That ought to look very nice when it's fitted!
-
Should hit up Home Depot for a coping saw. Next probably a sealer & varnish, or just use the varnish to seal the wood pores as I'm working with it. Wished was a hobby shop around here to where I could purchase small containers. Then have to figure out what glue or epoxy to use.
Just dawned on me that I forgot to order a pen, lol. Placed a small order with Swiss Knife Shop, and had to add a few smaller items to help meet the minimum order for the free first class shipping. Never ordered with them before. The Boise store where I got the Climber from had no pens...
Amazon's prices were double of what Swiss Knife Shop was on the pen part. $6.25 for a pen?? :ahhh -
@PTRSAK said:
Talking of logos for wooden scales...
This is a bit of an experiment testing a couple of things. Firstly to see how an "Ivory" cross inlayed into the wood looks and how easy the Tagua nut "vegetable ivory" is to work with and how well it wears.
I will finish these to fit a Recruit and give it a bit of pocket time with flashlight, keys and change for company.I think it will look pretty schmick myself.
Impressive. Dare I ask how you put the inlay in?
-
I cut the cross out of the slice of Tagua nut Ivory and then trace it on the wood. Then using Dremel and hobby knife I cut the recess about 1/2 way through the wood. The cross is a loose fit at this stage. I mix up a glue from Epoxy resin and sanding dust from scraps of the wood and use this to glue the cross in. The "glue" has a colour and texture similar to the wood and once sanded flush there is no gap around the edge of the cross.
As I said, this one is an experiment so it's only about 90% on the care and attention to detail, but I have never been one to polish a prototype.
-
@PTRSAK said:
I cut the cross out of the slice of Tagua nut Ivory and then trace it on the wood. Then using Dremel and hobby knife I cut the recess about 1/2 way through the wood. The cross is a loose fit at this stage. I mix up a glue from Epoxy resin and sanding dust from scraps of the wood and use this to glue the cross in. The "glue" has a colour and texture similar to the wood and once sanded flush there is no gap around the edge of the cross.As I said, this one is an experiment so it's only about 90% on the care and attention to detail, but I have never been one to polish a prototype.
Aye, have used that technique as a kid when making boomerangs. Something learned in shop class, to mix the sawdust you are using with Elmer's glue. Gives it color, bond, and allows sealing as the wood fibers are porous.

Not to side-track the topic, had this experimental (one time only) formica triangle boomerang idea where I had used sawdust and Super Glue as filler. Needed to put in angles to turn the boomerang (gyroscopic procession). Formica was so thin there was nothing to work with.
Also used aluminum rivets at each bind point as glue wasn't holding. Contact cement was the best to stick the formica pieces together but was no where sturdy for the forces induced by the flight properties of a boomerang. Super Glue stuck to anything. :D Fingers too!
It worked out, but the flight path was so erratic only its creator (me) was able to figure it out.
(Attached (ugly) photo)Later on in life, Herb A. Smith of Sussex, England, had used Paxolin material to break the world's distance record. Once word got out what he was using Volker Behrens and Al Gerhards started using it. Stuff was too expensive for me to ship some in. Gosh, how I'd luv to find a supplier - but it probably way too expensive to buy & ship.
I flew one of Herb's Torando's out over a 140 acre field, across the 6 lane freeway, and it still continued across the field on the other side before it ever lifted high into the sky. Trust me, I was sweating it the first throw. Had to lay it way over where you do not normally release a boomerang at - without severe consequences.
It roses to unimaginable height, about lost it in the afternoon sun. By the time my eyes adjusted it landed to the left of me four feet away! Glad it didn't hit me. :D
Could only fly it a few times before my shoulder felt like it was going to fall off. I really leaned into it. Fun times, will attach that one as well. Have 1 of 2 remaining. Someone stole my other. /grrFun times. Bought my first boomerang from Richard Harrison, The Boomerang Man, when he was in Monroe, Louisiana. First one was a Wycheproof (Australian), made by Bunny read. Handsome and attractive wood with Aussie motifs on the elbow. Great for display purposes.
Later on bought a special run of Lorin Hawe's M-17 in Coachwood & another in Silky Oak. The silky oak one was by far my favorite, and thus why I wanted it for the handles/scales of my first Victorinox knife.If it turns out good, as never made these before, then any subsequent Vic knives might be fashioned from this wood.
Also ordered some 1.5mm x 3mm flat-round neodymium magnets to put into the scales. Figure one to hold & touch the pin. Keep it held in there since the layer is aluminum, and also to keep it magnetized - if I ever need it. Figure would also put in two to hold the writing pen in, and maybe another for the tweezers.
The magnets are coming in a lot of 50, so I should have plenty! :ahhhHad figured you would have undercut the insignia into the wood with an exacto blade or scalpel. I have nothing that looks ivory or other wood to use - and no I'm not going to sabotage my boomerangs. Maybe I can get some down the road to add in later.
Thanks for the update. And I apologize for being windy again.

Edit: Correcting spelling errors. Spell checker is being lazy.
-
This is what I bought, http://www.ebay.com/itm/130835306097?
Enough there to make a dozen or more crosses. The red dye just sands off, only on the surface.
-
@PTRSAK said:
This is what I bought, http://www.ebay.com/itm/130835306097?Enough there to make a dozen or more crosses. The red dye just sands off, only on the surface.
Awesome. Just ordered some. My cc is hating me about now. :ahhh
Free shipping though.• Exotic Australian Wood
• Pen, pin, & spare toothpick to quality for free shipping from Swiss Knife Shop. Was cheaper than Amazon!
• 1.5 H x 3mm W neodymium magnets (50)
• Ivory Nut ShellsStill going to need to get some sort of glue or epoxy (any recommendations?), coping saw, sandpaper, ect.
When I kick the bucket someone's going to have fun with that Climber
But, you know, when I was searching for a 1961 six pence Australian coin that went MIA ran across a rather useful tool. A valve core tool. Then made me wonder if that hidden slot was big enough to fit in a flat valve core tool. Probably not.
Not seen a valve core tool on any multitool or even a hex/flat-hex bit valve core driver. Had thought E510 had fashioned a bit once...

Just about every vehicle still uses valve cores. They do get loose at times, and bicycles still use them - hisses at Schrader valves!
-
@PTRSAK said:
Talking of logos for wooden scales...
This is a bit of an experiment testing a couple of things. Firstly to see how an "Ivory" cross inlayed into the wood looks and how easy the Tagua nut "vegetable ivory" is to work with and how well it wears.
I will finish these to fit a Recruit and give it a bit of pocket time with flashlight, keys and change for company.I think it will look pretty schmick myself.




-
You drilled out the pins in the knife then pinged them over the wooden scales?

Don't think I'm that brave. Will use a glue or epoxy. :D
-
@papercut said:
Edrawing viewer for cad viewer or auto desk has one free one too.For the Free/Trial versions: AutoDesk did not wish to cooperate when printing to a specified size, and the other just wouldn't measure or print.
The pen scale looks like the regular scale, with the added pen channel. Thanks for the effort fellas, <u>is</u> highly appreciated.
The graphics files are immensely valuable. That really helps grasp the visual perspective in 3D-like captures. Perhaps other folks viewing this later on in the years will find them useful too.
Edit: The PDF file helps a lot as it easily allows for an actual sized print. 
-
Tagua Nut pieces arrived today, along with a package from Germany - Lowtech delivered goodies. :D
Took a bit of work to get the red off. That's one tough nut. They are thin enough to use a guitar picks, and each one has been drilled near the edge.

Not sure what sort of red material that coating is. Wonder if it can be soaked in something to remove that red substance? Maybe vinegar, to remove the red dye/coating.
-
Mate that looks GREAT


Peter any problems with the nut material getting through Oz customs being organic & all that
Does the dye seal it & make it ok to be brought into Oz

-
@Xelkos said:
Tagua Nut pieces arrived today, along with a package from Germany - Lowtech delivered goodies. :DTook a bit of work to get the red off. That's one tough nut. They are thin enough to use a guitar picks, and each one has been drilled near the edge.

Not sure what sort of red material that coating is. Wonder if it can be soaked in something to remove that red substance? Maybe vinegar, to remove the red dye/coating.
While i can´t help with the Nut´s coating, i am relieved to hear teh stuff made it safely to your door!
I´m looking forward to read about it in some other thread ;-). -
Mate that looks GREAT

Peter any problems with the nut material getting through Oz customs being organic & all that
Does the dye seal it & make it ok to be brought into Oz

didn't have any problem, can't remember what they put on the customs declaration.
Any secrets to getting the red dye off? That stuff is thick!
Heard not to soak the pieces as they can split and pull apart after gluing. Didn't read that before soaking two test pieces in white vinegar. The pieces came out with a slight spoon-shape to them but the dye did <u>not</u> budge.
Also read the nut is quite porous and absorbs.Did you oil it or rub a varnish the scales? I was considering a satin varnish finish.
Waiting for the wood. Thinking of going with one of these two crosses, or a roo. Undecided yet.
Could put the roo on the fat end, but not sure. This is my first time making SAK scales.Note: That's what a Tagua Nut looks like. Read they aren't more than egg sized. The tree is a palm.




-
the dye isn't thick, but it has soaked into the surface. When I did the inlay it was only to about 2/3of the thickness of the "ivory" so all the red got sanded off when I was shaping the scales.
-
Found out that the White Tagua Nut Slices are not dyed nor have any coating on them. Can save time on the whole 'sanding that thick dye off'.@Wanan Beads said:
Yes, Tagua Slices White is natural color. Not coated with any dyes.Silky Oak blanks arrived from Turning Timbers of Australia

Still awaiting the 1.5mm x 2mm flat round neodymium magnets.
Amazon/Magnetman
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login