Leatherman REBAR Multi-Tool
-
I just received a stainless and BO Rebar from Travis today.

'Bout time! I've been using mine or at least the HEADS of Rebars for over a month now!
Did you try to fit the Rebar pliers to the Surge? Did it fit without modding the safety's, being a smaller plier head than the ST300.
-
Maybe I've just overlooked it, but I can't find the date codes in my Rebar; the QC heads for the castings, yes, but no date codes.

-
-
I just received a stainless and BO Rebar from Travis today.

'Bout time! I've been using mine or at least the HEADS of Rebars for over a month now!
I never did it because the pivots don't line up. The distance when closed interfere.
Did you try to fit the Rebar pliers to the Surge? Did it fit without modding the safety's, being a smaller plier head than the ST300.
-
Interesting disassembly tools, how did you make them? Good job by the way. I love taking things apart too.
+1
I haven't seen those Disassembly tools before.+2 :)
@mtool78 said:
..leaving date stamps off is a sad news - but I can see that it means one procedure less on production line (saves some $)I could understand that. However, my Rebar has "B01" stamped inside of both handles, so no cost-cutting here.

-
Interesting disassembly tools, how did you make them? Good job by the way. I love taking things apart too.
+1
I haven't seen those Disassembly tools before.+2 :)
There are a couple of Leatherman Maintenance tools scattered across the world among MTO members. They were kindly donated by a member who used to do LM warranty repairs.
-
@enki_ck said:
There are a couple of Leatherman Maintenance tools scattered across the world among MTO members. They were kindly donated by a member who used to do LM warranty repairs.Oh... thank you for the info. Any idea what can I use instead for Rebar?
So far I used PST + Squirt combo to disassemble old-style SuperTool, PST and PST II, but these had knurled screws fully accessible while Rebar has handles kind of bulged around them (not sure how to say it properly in English). Any tips? -
@Gilliand said:
Oh... thank you for the info. Any idea what can I use instead for Rebar?
So far I used PST + Squirt combo to disassemble old-style SuperTool, PST and PST II, but these had knurled screws fully accessible while Rebar has handles kind of bulged around them (not sure how to say it properly in English). Any tips?Locking pliers is what I hear most around here. At least one to hold one side, the other maybe with normal pliers, or another locking pliers? Don't forget to heat up the screws, to melt the loctite.
-
And I got this in today.


-
I like the gold

-
I'm not always a fan of pimped MT's, but that gold Rebar does look kinda cool.
-
I think it's time to rotate my rebar into my work edc. It's one of my favorite Leatherman Tools.
-
If there was only a way to sneak in a diamond-coated file ...
-
@Xelkos said:
If there was only a way to sneak in a diamond-coated file ...I know, that's the thing I don't get. Why don't all Leatherman files (and Victorinox Swisstools, Spirits) come standard with a diamond coated side? I see little purpose for both sides of the file being basically the same thing. Diamond coated is rather useful.
-
@Xelkos said:
If there was only a way to sneak in a diamond-coated file ...
I know, that's the thing I don't get. Why don't all Leatherman files (and Victorinox Swisstools, Spirits) come standard with a diamond coated side? I see little purpose for both sides of the file being basically the same thing. Diamond coated is rather useful.
When we asked Leatherman this they said that their research suggested Tradesman preferred their heavy duty MTs to have LM's standard file to the diamond file
hence it not being available on the SuperTool 300 , Rebar etc
. I love the diamond file , I suspect it may well come down to a warranty issue as the diamond file if abused will wear out a lot quicker than the standard file

-
@Xelkos said:
If there was only a way to sneak in a diamond-coated file ...
I know, that's the thing I don't get. Why don't all Leatherman files (and Victorinox Swisstools, Spirits) come standard with a diamond coated side? I see little purpose for both sides of the file being basically the same thing. Diamond coated is rather useful.
When we asked Leatherman this they said that there research suggested Tradesman preferred their heavy duty MTs to have LM's standard file to the diamond file
hence it not being available on the SuperTool 300 , Rebar etc
. I love the diamond file , I suspect it may well come down to a warranty issue as the diamond file if abused will wear out a lot quicker than the standard file

Oh I see. Thanks for the informative reply MultiMat
Still don't like it though. The diamond file is nice to have, but then again, I'm no Tradesman either, so my opinion on that may not be valid
However, for my own preference, a diamond side is better :P -
The gold Rebar is droolworthy. :D
-
Does anyone know the exact specs, dimensions, measurements of the pivots and screws on the lower/tool end (and plyers end if you have them) of the Rebars? I am in the process of swapping out for custom machined ones or some from Knifekits.com. Do they HAVE to be D style pivots? Thanks
-
Sorry no help here
Hopefully someone will be along that knows though 
Either way, welcome to

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
and 8)