30 Day Coghlan's Campers Tool Challenge!
-
@Nhoj said:
Great work still.
Maybe instead of using the knife blade you could use the can opener to open the can like a normal food can. I have turned soda cans into cups using the can opener on my wave before.I liked this idea, so I tried it:
The results are pretty clear. But good news:

"And I said 'yeah, baby, yeah!' "The Leatherman can opener did a great job, so props for that. It's just too bad that if I need to do this again next week, I'll still have to use Campy.
Both of them worked when I tried to open the can from the top (like a food-type can), but Campy was pretty slow, since the relatively unpronounced hook under the can opener had trouble latching under the lip of the can (Coke Zero this time, since I ran out of empty Orange Crushes).
Here are the two can openers, staring each other down:

Only one of these is a can opener. The other one is a can't opener.The Leatherman opener is sharpened. The Coghlan's one, however, is the bluntiest blunter in blunt town. Without hooking under the rim of a can for leverage, Campy's can opener...can't.
-
Can't opener?
Try and say that three times fast!
-
instead of using the can opener to remove the entire top portion of the can, use it like you would when opening a food can... remove the top while leaving the top rim intact. See how that works.
-
@Jothra said:
Both of them worked when I tried to open the can from the top (like a food-type can), but Campy was pretty slow, since the relatively unpronounced hook under the can opener had trouble latching under the lip of the can (Coke Zero this time, since I ran out of empty Orange Crushes).It didn't really stand out in my post because I didn't get pictures.
-
I see
-
Hilariously, I got it wrong, did it again, and forgot the pictures the second time.
For the record, from-the-top is a way better idea, so I'm doing that from now on. Thanks, Nhoj!
-
:D You're welcome
-
You are doing Gods work son.

-
Loving your reports mate. :D
-
Day 26
Today was Jothra Is A Meanie Day! I used Campy for all kinds of things, some of which I happen to know are very bad ideas, from a tool longevity point of view.First thing upon arriving at work, I unlocked the most important door on site, which someone had locked overnight for some reason. This is the most useful the large screwdriver has been:

If a Porta Potty door doesn't open, it's really just a smelly paperweight.Then, after some dry-pack grouting (fun, if you're dumb like me), I had to break off a bunch of form pins from the original foundation pour. Normally this is as easy as hitting them a couple of times with a hammer—in today's case, a mini-sledge—but one pin was bent down so close to the wall that I needed to pry it up before I could even hammer it:

See how bad an idea this is? This is a really bad idea.But, maybe surprisingly, it worked, and I finally hammered off the blasted pin:

I've only very rarely pried with the plier tips, because breaky breaky!Next, while working on the pin-smashing, I found a column base I had grouted, but forgot to clean up:

Maybe it's not important, but I like to leave a nice, clean-cut column base.My margin trowel was way on the other end of site (and it's a big site). What to do?
You're not going to believe this, sports fans, but the fish scaler actually did something useful, like, for real.

The picture doesn't really do its awesomeness justice.Finally, someone remembered to bring the grinder, but it needed a blade change. So, do you think we had the special grinder wrench on site?
Bwa ha ha! No.
Good news, though! A time-tested trick performed by no fewer than three (3) of my different Leatherman tools:

No grinder tool? No problem! Like a charm!Don't worry. The grinder was unplugged at the time.
This was a pretty punishing but successful day for poor ol' Campy.
-
I agree you have good write ups. And your added jokes in italics are very funny. 
-
@Lynn LeFey said:
You're not going to believe this, sports fans, but the fish scaler actually did something useful, like, for real.

I still won't be running out to buy tools with fish scalers, but I guess the trick is to use the tools you have, not the tools you want.
Thanks, everybody! More grouting tomorrow? More steel tie-wire? More grinding? A nice panini? Stay tuned!
-
I just tried taking the top off of a soda can with my can opener (on the same tool with different name plastered on it). Strange thing happened... after about 4 or 5 cuts, the top started to split cleanly along a seam, like the pre-scored area of a pop-top. The whole top came off freakishly cleanly. I'll see if I can get pics in the morning.
-
Sorry for the double-post, but here's a pic of the can mentioned above.
The opener started in from the edge, and began creeping toward the rim. Then by the forth or so puncture, it started splitting cleanly along a seam. When I got back around to the start, it removed even most of the bits that I'd missed to start with. Very, VERY clean. Freaky.

-
I'm having trouble replicating your results, though I still get a pretty clean cut if I poke into that little trench thing.
-
I have no idea if my results were typical, or if it was just this canning facility, this particular batch, or what.
Also, if you just cut the lid off normally, you can use the handle of the tool to press down the jagged material inside the lip of the can to make it a little safer, if need be.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


:D :D