My small adventure into 58mm SAK modding!
-
It´s looking good and will get better with age and patina.
-
Brass is excellent - Syph007...stunning work sir!
I was directed here from another forum to look at your work on SAKs and I can see why you were recommended.

kawasemi
-
I have been working on the 58 mm pliers mod off and on for awhile now, and I have tried so many ideas for locking the pliers that I have completely abandoned a 'simple' solution to this, and am just going to make the complicated version.
Since I was trying to make a mini wenger pocket grip anyway, I decided to make a locking mechanism similar to that one.
Here is a pic of where I am so far.

The diagram hopefully explains this well enough. I JB welded in a piece of drill bit shank into the pliers to act as the retaining pin.

Part of the liner will slide and hold the pliers shut. That part is roughed from 0.032" Ti and will be plenty strong. I got to use my mill to make that tang and slot and it worked out sweet. There is 0.001" clearance on those parts and they slide perfectly.
Stay tuned! :D
-
I knew it had something to do whit those pliers as soon as I saw this thread updated. :D Interesting decision with the sliding liner lock. You said a couple of times that galling of titanium against titanium is a problem. How are you handling it here with the to sliding liner parts?
And if that partial layer is sliding, what about the other layers that require the 4th pin?
-
You are correct any parts where Ti and stainless touch have to be carbidized, except the inner part of the lock as I want it to be sticky there.
I already prototyped the 3/4 pin split system and it worked fine. Basically if you picture a rambler with this layer in the middle, 3 pins will go all the way though, and the other pin will only hold its half of the sak together.
It was the only way to have the pliers down further inside the SAK, and it make the whole package a really nice keychain accessory. The downside of course is that its way more complicated to build.
-
Correct me if I'm wrong, and this is merely an I'm trying to understand it question, Wenger Pliers wouldn't work because its spring is activated by the layer spring (slipjoint one) right?
Can't wait to see it done, a would be amazed even if it used a simple bail that folded to hold the pliers,
the sliding lock just forces me to put on my "absolutely must have otherwise I'll die" list.Congrats for the amazing work Syph, you never ceases to amaze me, thank you for that!!
-
I finally got around to making a Ti 58 with tweezers on the back scale. Way more annoying then I thought it would be, but it does work. The Ti scales I use are thinner than standard ones so the tweezer head needed to be trimmed a bit, but it worked out ok.






-
NICE. Ti tweezers would be over the top.
-
NICE. Ti tweezers would be over the top.
<u>Skip that! Ti toothpick, that would be awesome!!!</u>

Amazing piece!

More useful for digging out splinters than picking teeth. in fact it's too sharp for me to be putting in **my **mouth...
-
NICE. Ti tweezers would be over the top.
<u>Skip that! Ti toothpick, that would be awesome!!!</u>

Amazing piece!

More useful for digging out splinters than picking teeth. in fact it's **too sharp for me to be putting in **my mouth...
Thats not what she said...

-
I had someone wanting an alox minichamp with usb so I gave it a go. My first peen job on 58 alox and it turned out ok. I for sure still prefer the screw methods though. :D




-
Nice work :)
So, how are you on the pliers in a 58mm mod?

-
-
-
I'm glad you used the spring keyring hole. The one on the plastic flipper is just awful.
Did you get all pin heads to end up the same diameter? That's the tricky part when doing 58mm.
Edit: 666th post!

-
I have a bunch of requests in the queue for Ti minichamps and ramblers so I decided to try to build 4 at once to speed things along.
I took some pics of the Ti sandwiches during the process. I never could have done this without the milling machine. Ti is a royal pain to work with, but so nice when finished. :D
It mills very nicely though so thats my prefered way to cut it. I use a 1/8 milling bit to cut the sheets into strips, and then into rectangles.








-
Syph007 58mm assembly line. :ahhh
Looking good.

-
I asked my waterjet guy about doing a run of 58 parts to be able to make a buch, but those small holes are too small to waterjet, so doing them this way is still going to be the best until I finish the CNC conversion, then I can have a tool spot the holes instead of using liners to get them drilled just right.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

