My small adventure into 58mm SAK modding!
-
You are correct any parts where Ti and stainless touch have to be carbidized, except the inner part of the lock as I want it to be sticky there.
I already prototyped the 3/4 pin split system and it worked fine. Basically if you picture a rambler with this layer in the middle, 3 pins will go all the way though, and the other pin will only hold its half of the sak together.
It was the only way to have the pliers down further inside the SAK, and it make the whole package a really nice keychain accessory. The downside of course is that its way more complicated to build.
-
Correct me if I'm wrong, and this is merely an I'm trying to understand it question, Wenger Pliers wouldn't work because its spring is activated by the layer spring (slipjoint one) right?
Can't wait to see it done, a would be amazed even if it used a simple bail that folded to hold the pliers,
the sliding lock just forces me to put on my "absolutely must have otherwise I'll die" list.Congrats for the amazing work Syph, you never ceases to amaze me, thank you for that!!
-
I finally got around to making a Ti 58 with tweezers on the back scale. Way more annoying then I thought it would be, but it does work. The Ti scales I use are thinner than standard ones so the tweezer head needed to be trimmed a bit, but it worked out ok.






-
NICE. Ti tweezers would be over the top.
-
NICE. Ti tweezers would be over the top.
<u>Skip that! Ti toothpick, that would be awesome!!!</u>

Amazing piece!

More useful for digging out splinters than picking teeth. in fact it's too sharp for me to be putting in **my **mouth...
-
NICE. Ti tweezers would be over the top.
<u>Skip that! Ti toothpick, that would be awesome!!!</u>

Amazing piece!

More useful for digging out splinters than picking teeth. in fact it's **too sharp for me to be putting in **my mouth...
Thats not what she said...

-
I had someone wanting an alox minichamp with usb so I gave it a go. My first peen job on 58 alox and it turned out ok. I for sure still prefer the screw methods though. :D




-
Nice work :)
So, how are you on the pliers in a 58mm mod?

-
-
-
I'm glad you used the spring keyring hole. The one on the plastic flipper is just awful.
Did you get all pin heads to end up the same diameter? That's the tricky part when doing 58mm.
Edit: 666th post!

-
I have a bunch of requests in the queue for Ti minichamps and ramblers so I decided to try to build 4 at once to speed things along.
I took some pics of the Ti sandwiches during the process. I never could have done this without the milling machine. Ti is a royal pain to work with, but so nice when finished. :D
It mills very nicely though so thats my prefered way to cut it. I use a 1/8 milling bit to cut the sheets into strips, and then into rectangles.








-
Syph007 58mm assembly line. :ahhh
Looking good.

-
I asked my waterjet guy about doing a run of 58 parts to be able to make a buch, but those small holes are too small to waterjet, so doing them this way is still going to be the best until I finish the CNC conversion, then I can have a tool spot the holes instead of using liners to get them drilled just right.
-
So, how are you doing on the pliers?

(Am I being too impatient?
) -
@bmot said:
So, how are you doing on the pliers?

(Am I being too impatient?
)Changed gears on that one, going with a much simpler way to lock the pliers closed. I'll have pics of that in a bit. The sliding thing was way too complicated and well it just got out of hand. For the purpose of simplicity I got a better idea to just use a small thick O ring anchored into the SAK and then locked into a groove on the pliers handle to hold it down.
Sometimes simple is just a better idea.
-
Re: galling of dissimilar metals.
Galling is only a serious problem when the dissimilar parts are in close contact, and under pressure. Think of a Ti screw tightened into a steel tapped hole, or something similar.
I doubt a 58mm SAK would need preventative measures to prevent galling, as the loads are not high enough (possible exception being the assembly screws/pins), but there is a preparation that helps prevent galling, even when the loads are high. There's an anti-seizure "lubricant" called Ti-Prep, made by Finish Line. I used it quite a bit when I was into lightweight bicycles with Ti componentry and threading.......never had a thread seize on me.
I checked downstairs, I still have most of a syringe-full left. -
@neillcurrie said:
Re: galling of dissimilar metals.Galling is only a serious problem when the dissimilar parts are in close contact, and under pressure. Think of a Ti screw tightened into a steel tapped hole, or something similar.
I doubt a 58mm SAK would need preventative measures to prevent galling, as the loads are not high enough (possible exception being the assembly screws/pins), but there is a preparation that helps prevent galling, even when the loads are high. There's an anti-seizure "lubricant" called Ti-Prep, made by Finish Line. I used it quite a bit when I was into lightweight bicycles with Ti componentry and threading.......never had a thread seize on me.
I checked downstairs, I still have most of a syringe-full left.When I assembled the first Ti minichamp I did, the tools were pretty sticky and they would get a gouged round groove on all the tools. The carbidizer takes only minutes to use to coat the friction surfaces so thats been a fine solution. It was a really bad problem on the 93mm Ti ones I did, so much so that the tools would not even move freely at all. The first couple I would use
I also made a Ti tool and what I did on that was to carbidize the spring itself and that let the Ti pivot move freely.
The one trick though about doing the carbide layer deposit is that it goes does a bit rough, but I wet sand it with 800 grit and its silky smooth.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

