Can Opener Comparison
-
@Nix said:
You made that cut look quite expert. I'm impressed by the even and smooth cuts.
I was not trying to make a nice cut. That was just rocking the multi-tool up and down, and spinning the can. Very natural movements, and I did not have to compensate for, or adjust to anything, like weird balance, awkward grip, slipping, going off kilter.
That's just how the Leatherman claw performs. Every tool that has that can opener, Rebar, Signal, Surge, Charge, etc, they'll all do a fantastic job. -
You are becoming the can opener expert RP

-
@Aloha007 said:
Very well done.
I am a fan of the Victorinox can opener and use them often enough. Some cans do have the pull tab but a good many dont. I like the forward style vs Wenger style opening. Its probably familiarity. I must have tried the LM opener but nothing negative or positive comes to mind. I am certainly happier using the Vic opener for now.
I liked how easy the process was with the Cadet. Once I managed not to slip, Victorinox was just as good. I can't say I am used to one or the other, so for me it comes down to ease of use. Leatherman and Vic, both are great. I tested the Coast quarter-circle, and it did not go well. I'll test the Gerber on an entire can.
I do like the claw a little more. There is no learning curce with a Leatherman claw, which is why I like it the most. Wenger claws were also great once I identified the technique quirk. The Schrade kinda worked. I also liked the Bear and Son one, so I'll open a whole can with that one too. And the Ganzo. The BuckTool, well, that's in a league of its own.
I'll also revisit the Juice, Safari Hunter, and Bantam. I am a bit curious if the combo tools will hold their own.
-
Another try with the Wave.
I thought I'd eliminate one blade spine digging into my fingers, by opening one handle. This configuration brings the inside edges of the handle against your fingers. Although quite comfortable, this means that you will be holding on half the tool.
I have large size hands, and I found that having only one handle in my palm while opening the can was not preferable. Instead, having both handles folded up fills my palm better, giving me a better grip, causing less fatigue, and providing better control of the tool. Holding on one handle might be better for smaller hands.
Also, if you only hold onto one handle, the other will hang through the back of your hand. Of course, these are afterthoughts, as the can opener is a great performer. The process will be easy and consistent, with a clean cut, so whichever way you end up holding the tool is up to personal preference.
-
Juice CS4
Original attempt
Spoiler:
@ReamerPunch said:
Juice
0 points for punching through. The piercing point is blunt and not at the best angle to punch through.
1 for comfort. The edges dig into my hands, and so does the corkscrew. This is the old design, so maybe now it's better?
2 for not jamming.
2 for cutting.
2 for not slipping.
Total: 7

Entire can
Going full circle on a can was a similar experience to the original attempt. The edge has no bevel, making the piercing point blunt. It might have performed better if the point met the can lid at a better angle, but as it is, piercing through takes a significant amount of force, compared to a sharpened claw or quarter-circle.
Going full circle made even more evident how average the ergonomics are. The corkscrew reminded me of SOG gears digging into my hand, and though not as bad, it was more uncomfortable than the Wave/Charge blade spine.
Compared to the original attempt, it lost a point for cutting. That is mainly because it does not exactly cut. With a sharpened can opener, be it a Leatherman claw or a Victorinox quarter-circle, you can feel the edge cutting through the lid. The Juice's blunt edge just pushes the lid downwards, and being rigid, the lid just tears along the previous 'cut'. However, it is quite effective, thanks to the great hook which holds onto the rim, and the edge being at a good position to trace around the lid. If it were sharper, it would have been better, but it still works. Also it left a sharp edge behind, both on the can and on the lid. No surprises there, considering the lid was essentially broken off instead of cut.
Absolutely no slipping or jamming as well.0 points for punching through.
1 for comfort.
2 for not jamming.
1 for cutting.
2 for not slipping.
Total: 6




-
So now that Leatherman has a quarter-circle, all big four brands have a quarter-circle.
I do not know how I feel about this.
The standard LM claw is excellent, why did they go with the quarter-circle for the Free series?
-
Well, you can free space on your Zombie Survival Kit and not include a can opener or use an MT or SAK without one. Because: https://www.youtube.com/watch?v=lhT7VNRFkx4
Nobody needs a can opener when you have pavements!

-

Is the food safe to eat after all that grinding? -
@ddogu said:
Well, you can free space on your Zombie Survival Kit and not include a can opener or use an MT or SAK without one. Because: https://www.youtube.com/watch?v=lhT7VNRFkx4Nobody needs a can opener when you have pavements!

Or alternatively like the resident female savage of the household: "I didn't need a can opener. I just borrowed one of your knives instead". :ahhh I told her she could keep the knife as a gift - no need to return it. She then commented that an unsharp knife with chipped edges wasn't much of a gift..! ::)
-
That’s a different way of opening a can

-
@ReamerPunch said:
As is this.
https://www.youtube.com/watch?v=Uj0hU0uDy9ESuch a good video, very interesting technique! Thanks for sharing!
-
I've never had much luck with the quarter circle forward opening Victorinox over the rear opening LM Claw which I vastly prefer. The Vic keeps jamming up. It's also considerably slower and leaves a more jagged edge inside the can. No doubt I'm doing something wrong but I get no brainer perfect results with the LM. Can anyone point me towards the correct procedure to use the quarter circle more efficiently? Or am I just hamfisted? :D
-
@pomsbz said:
I've never had much luck with the quarter circle forward opening Victorinox over the rear opening LM Claw which I vastly prefer. The Vic keeps jamming up. It's also considerably slower and leaves a more jagged edge inside the can. No doubt I'm doing something wrong but I get no brainer perfect results with the LM. Can anyone point me towards the correct procedure to use the quarter circle more efficiently? Or am I just hamfisted? :DI don't know whether there's a right way to it. I actually use it backwards and it's faster for me, meaning holding it in right hand, I rotate the can counter-clockwise. Have you tried counter-clockwise vs clockwise?
-
@pomsbz said:
I've never had much luck with the quarter circle forward opening Victorinox over the rear opening LM Claw which I vastly prefer. The Vic keeps jamming up. It's also considerably slower and leaves a more jagged edge inside the can. No doubt I'm doing something wrong but I get no brainer perfect results with the LM. Can anyone point me towards the correct procedure to use the quarter circle more efficiently? Or am I just hamfisted? :DI also had some trouble with the Victorinox one at first. I kept slipping off the can, and the edge will be a little jagged until you get good with it.
Check the video I posted above. He shows the regular process starting at 1:11. It is just a matter of getting used to it, and improving your results I think.That is why I prefer the Leatherman claw. There is no learning curve. Perfect easy results every time.
-

I also started playing with the different styles and found the LM claw to be the easiest and most consistent in cutting the tops out of soda cans(a lot of can openers just can't do it at all) and regular cans. I do like having the driver tip on the Vic though. So they kind of even out in a way. :)
-
NexTool Flagship Pro/Xiaomi Huohou
0 points for punching through.
0 for comfort.
0 for not jamming.
-5 for cutting.
-5 for not slipping.
Total: -10
Punching through is difficult. The edge is blunt and the tip is rounded off. The left edge of the hook, the edge that would grab on the rim, is rounded off. On a proper can opener, the hook has a 90° edge, so that the can opener holds onto the lip, which provides the necessary leverage for the tip to pierce. On this, the hook just slips off with the slightest force applied to the edge. It takes a considerable amount of force to pierce, all the while being careful to keep the can opener in place.
This makes the whole process an ordeal. For right-handed use, it was difficult to pierce, and impossible to continue on the initial cut. Left-handed is marginally better, since the right edge of the hook has a 90° edge and holds onto the rim.

Cutting left-handed was difficult and awkward, as I am right-handed. Tracing along is painful, since the cutting edge is more of a breaking edge.

Blunt as it could be, the edge slid along the rim, and there is no piercing point to speak of. I had to constantly adjust positioning, and reached about a quarter of the rim. After many tries to continue cutting/breaking the rim, it would not cut along beyond that point.

It took so much force to cut, that I bent the stop pin that provides retention. Now the can opener has play when deployed. Not a big issue. Why would I deploy the can opener? It cannot open cans. If I want to get a sore hand, and mangle a can, I'll just punch the can.

After five minutes of battling the can with the wrong tool and losing, I switched to the Leatherman Core. Just a few seconds, and I cut easily, painlessly, effortlessly, consistently, and effectively around the rim, never slipping off, going through mangled spots with no issues, until the can was nicely opened.

The Flagship Pro's can opener did not even survive a quarter of one can lid.
Left-handed, since right-handed I could only do a single cut. 
What a joke of an implement. What an insult to release this tool with such a terrible can mangler. Is testing not a part of the development process?
Is it really that difficult to try and open a can before you release it? I tried one can and the stop pin bent. I had not even opened one single can!
The can opener on this tool is a waste of space. Beyond unreliable to open a can. Too bad.
-
Great tests again RP

-
-
26:56 - Flagship can opener vs Roxon Storm can opener.
Note that diezelle has the updated version, with the can opener in the proper position and sharpened properly.- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
